TJA1054AT/VM,518 NXP Semiconductors, TJA1054AT/VM,518 Datasheet - Page 6

• Manufacturer Part Number: TJA1054AT/VM,518
• Description: IC TXRX CAN FAULT-TOL 14SOIC
• Manufacturer: NXP Semiconductors
• Type: Transceiverr

Specifications of TJA1054AT/VM,518

• Package / Case: 14-SOIC (3.9mm Width), 14-SOL
• Number Of Drivers/receivers: 1/1
• Protocol: CAN
• Voltage - Supply: 4.75 V ~ 5.25 V
• Mounting Type: Surface Mount
• Product: Controller Area Network (CAN)
• Number Of Transceivers: 1
• Data Rate: 125 KBd
• Supply Voltage (max): 5.25 V
• Supply Voltage (min): 4.75 V
• Supply Current (max): 27 mA
• Maximum Operating Temperature: + 150 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Power Down Mode: Sleep/Standby
• Operating Supply Voltage (max): 5.25V
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (min): 4.75V
• Package Type: SO
• Operating Temperature (max): 150C
• Operating Temperature (min): -40C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 14
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-5077-2; 935287974518; TJA1054AT/VM,518

NXP Semiconductors
TJA1054A
Product data sheet
Table 4.
[1]
[2]
Failure 6 is detected if the CANL bus line exceeds its comparator threshold for a certain
period of time. This delay is needed to avoid false triggering by external RF fields. After
detection of failure 6, the reception is switched to the single-wire mode through CANH;
the CANL driver is switched off and the RTL bias changes to the pull-up current source.
Recovery from failures 3, 3a and 6 is detected automatically after reading a consecutive
recessive level by corresponding comparators for a certain period of time.
Failures 4 and 7 initially result in a permanent dominant level on pin RXD. After a time-out
the CANL driver is switched off and the RTL bias changes to the pull-up current source.
Reception continues by switching to the single-wire mode via pins CANH or CANL. When
failures 4 or 7 are removed, the recessive bus levels are restored. If the differential
voltage remains below the recessive threshold level for a certain period of time, reception
and transmission switch back to the differential mode.
If any of the wiring failure occurs, the output signal on pin ERR will be set to LOW. On
error recovery, the output signal on pin ERR will be set to HIGH again. In case of an
interrupted open bus wire, this failure will be detected and signalled only if there is an
open wire between the transmitting and receiving node(s). Thus, during open wire
failures, pin ERR typically toggles.
During all single-wire transmissions, ElectroMagnetic Compatibility (EMC) performance
(both immunity and emission) is worse than in the differential mode. The integrated
receiver filters suppress any HF noise induced into the bus wires. The cut-off frequency of
these filters is a compromise between propagation delay and HF suppression. In
single-wire mode, LF noise cannot be distinguished from the required signal.
Failure
1
2
3
3a
4
5
6
6a
7
A weak termination implies a pull-down current source behavior of 75 μA typical.
A weak termination implies a pull-up current source behavior of 75 μA typical.
Description
CANH wire
interrupted
CANL wire interrupted on
CANH short-circuited
to battery
CANH short-circuited
to V
CANL short-circuited
to ground
CANH short-circuited
to ground
CANL short-circuited
to battery
CANL short-circuited
to V
CANL and CANH
mutually
short-circuited
Bus failures
CC
CC
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 3 August 2010
Termination
CANH (RTH)
on
weak
weak
on
on
on
on
on
[1]
[1]
Termination
CANL (RTL)
on
on
on
on
weak
on
weak
on
weak
[2]
[2]
[2]
Fault-tolerant CAN transceiver
CANH
driver
on
on
off
off
on
on
on
on
on
CANL
driver
on
on
on
on
off
on
off
on
off
TJA1054A
© NXP B.V. 2010. All rights reserved.
Receiver
mode
differential
differential
CANL
CANL
CANH
differential
CANH
differential
CANH
6 of 27