TJA1054AT/VM,518 NXP Semiconductors, TJA1054AT/VM,518 Datasheet - Page 16

• Manufacturer Part Number: TJA1054AT/VM,518
• Description: IC TXRX CAN FAULT-TOL 14SOIC
• Manufacturer: NXP Semiconductors
• Type: Transceiverr

Specifications of TJA1054AT/VM,518

• Package / Case: 14-SOIC (3.9mm Width), 14-SOL
• Number Of Drivers/receivers: 1/1
• Protocol: CAN
• Voltage - Supply: 4.75 V ~ 5.25 V
• Mounting Type: Surface Mount
• Product: Controller Area Network (CAN)
• Number Of Transceivers: 1
• Data Rate: 125 KBd
• Supply Voltage (max): 5.25 V
• Supply Voltage (min): 4.75 V
• Supply Current (max): 27 mA
• Maximum Operating Temperature: + 150 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Power Down Mode: Sleep/Standby
• Operating Supply Voltage (max): 5.25V
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (min): 4.75V
• Package Type: SO
• Operating Temperature (max): 150C
• Operating Temperature (min): -40C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 14
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-5077-2; 935287974518; TJA1054AT/VM,518

NXP Semiconductors
Table 9.
V
ground; unless otherwise specified.
[1]
[2]
[3]
[4]
TJA1054A
Product data sheet
Symbol
t
n
n
rec
CC
det
rec
= 4.75 V to 5.25 V; V
All parameters are guaranteed over the virtual junction temperature range by design, but only 100 % tested at T
wafer level, and above this for cased products 100 % tested at T
For bare die, all parameters are only guaranteed if the back side of the die is connected to ground.
A local or remote wake-up event will be signalled at the transceiver pins RXD and ERR if V
To guarantee a successful mode transition under all conditions, the maximum specified time must be applied.
Dynamic characteristics
Parameter
failure recovery time
pulse-count failure
detection
number of
consecutive pulses
for failure recovery
BAT
Fig 4. Timing diagram for dynamic characteristics
= 5.0 V to 27 V; V
V
Δ V
V
V
V
CANH
CANL
CAN
RXD
TXD
[1][2][3]
V
diff
Conditions
normal operating mode
low power modes;
V
difference between CANH
and CANL; normal operating
mode and failures 1, 2, 5
and 6a;
pin ERR becomes LOW
on CANH and CANL
simultaneously;
failures 1, 2, 5 and 6a
…continued
= V
BAT
failures 3 and 3a
failures 4 and 7
failure 6
failures 3, 3a, 4 and 7
All information provided in this document is subject to legal disclaimers.
CANH
= 12 V
STB
− V
t
PD(L)
CANL
= V
Rev. 5 — 3 August 2010
CC
; T
vj
=
amb
−
40
= 25 °C, unless otherwise specified.
°
C to +150
Min
0.3
7
125
0.3
-
-
°
C; all voltages are defined with respect to
BAT
Fault-tolerant CAN transceiver
= 5.3 V to 27 V (see
Typ
-
-
-
-
4
4
t
PD(H)
TJA1054A
Max
1.6
38
750
1.6
-
-
amb
© NXP B.V. 2010. All rights reserved.
= 125 °C for dies on
Table
015aaa176
V
0 V
5 V
3.6 V
1.4 V
0 V
2.2 V
−3.2 V
−5 V
0.7V
0.3V
4).
CC
Unit
ms
μs
μs
ms
CC
CC
16 of 27