AVL4000-N04-5DZM SMC Corporation, AVL4000-N04-5DZM Datasheet - Page 4

• Manufacturer Part Number: AVL4000-N04-5DZM
• Description: Valve, Soft Start Up w/ Lock Out and Solenoid Valve 24VDC, Port Size 1/2
• Manufacturer: SMC Corporation
• Type: Soft Start Upr

Specifications of AVL4000-N04-5DZM

• Body Size: 1⁄2
• Brand/series: AV Series
• Coil Voltage: 24 VDC
• Configuration: with Lock Out
• Connection Type: D Type DIN with M12 Connector, Indicator Light and Voltage Suppressor
• Pressure Range: 30 to 150 psi
• Primary Type: Solenoid Valve
• Size, Port: 1⁄2" NPT
• Temperature, Ambient: 32° to 140°F
• Terminal Type: D Type DIN Connector
• Thread Type: 1⁄2" NPT
• Valve Type: Soft Start Up
• Voltage, Coil: 24 VDC

14-3-4
1. Use clean air.
1. Install air filters.
2. Implement countermeasures by installing after-
1. Do not use valves in such environments where
2. Do not use in an explosive environment.
3. Do not use in locations influenced by vibrations or
4. A protective cover, etc., should be used to shield
5. Shield valves from radiated heat generated by
6. Take suitable protective measures in locations
7. In a dusty environment or when valve switching
Be sure to read before handling. Refer to pages 14-21-3 to 14-21-4 for Safety Instructions and Common Precautions.
Do not use compressed air which contains chemicals,
synthetic oils containing organic solvents, salts or corrosive
gases, etc., as this can cause damage or malfunction.
Install air filters close to valves at their upstream side. A
filtration degree of 5 µm or less should be selected.
cooler or air dryer, or water separator, etc.
The air including excess drain may result in a malfunction of
valves and other pneumatic equipment. Implement
countermeasures by installing after-cooler or air dryer, or
water separator, etc.
corrosive gases, chemicals, or brine or water or
steam is airborne, or where valves can be directly
exposed to any of those.
impacts.
valves from direct sunlight.
nearby heat sources.
where there are contacts with water droplets, oil, or
welding spatter, etc.
noise is intrusive, install a silencer in the R port to
prevent dust from entering, and to reduce noise.
Warning
Caution
Warning
Operating Environment
Air Supply
Precautions
1. Perform maintenance and inspection as shown in
2. Equipment removal and supply/exhaust of
3. Low frequency operation
4. Manual override operation
1. Drain removal
Choke flow: (P
Note 1) Formulas above are applied to pneumatics only.
Subsonic flow: when (P
How to Find the Flow Rate
the instruction manual.
If handled improperly, damage may occur in machine or
equipment or an operational error may result in.
compressed air
When equipment is removed, first confirm that measures are
implemented to prevent dropping of workpiece and runaway of
equipment, etc. Then cut the supply pressure and power, and
exhaust all compressed air from the system using its residual
pressure release function.
Valves should be switched at least once every 30 days to
prevent malfunction. (Use caution regarding the air supply.)
When the manual override is operated, connected equipment
will be actuated.
Confirm the safety before operating.
Remove drain from air filters periodically.
Warning
Caution
Q = 120 x S x (P
Q = 240 x S x
Q: Air flow rate [
S: Effective area (mm
P
P
t:
2
1
2
+ 0.1)/(P
: Upstream pressure [MPa]
: Downstream pressure [MPa]
Air temperature [°C]
(P
1
Maintenance
2
+ 0.1) x
1
+ 0.1)/(P
1
+ 0.1) ≤ 0.5
– P
2
)(P
l
/min (ANR)]
1
2
273 + t
+ 0.1) > 0.5
+ 0.1) x
2
293
)
(At air temperature of 20°C)
273 + t
293