ISE30A-N01-P-L SMC Corporation, ISE30A-N01-P-L Datasheet - Page 14

• Manufacturer Part Number: ISE30A-N01-P-L
• Description: Sensor, High-Precision Digital Pressure (positive), 1-PNP Open Collector Output
• Manufacturer: SMC Corporation

Specifications of ISE30A-N01-P-L

• Display: 4-Digit, 7 Segment, 2-Color LCD (red/green)
• Function: High Precision, Digital Positive Pressure Sensor
• Ip Rating: IP 40
• Mounting Type: Panel or Bracket
• Output: 1 - PNP Open Collector
• Primary Type: Pressure
• Range, Measurement: -0.100 to 1.000 MPa
• Sensing Mode: Air, Non-Corrosive Gas, Non-Flammable Gas
• Termination: Lead Wire, Oilproof Heavy Duty Vinyl Cable
• Voltage, Supply: 12 to 24 VDC

1. Incorrect wiring can damage the switch and cause
2. Do not attempt to insert or pull the pressure sen-
3. Wire separately from power lines and high voltage
4. If a commercial switching regulator is used, make
1. Do not drop, bump, or apply excessive impacts (100
2. The tensile strength of the cord is 35 N. Applying
3. Do not exceed the screw-in torque of 7 to 9 N·m
4. Do not use pressure sensors with corrosive
5. Allow a sufficient margin of tube length in piping
6. When a brand of tubing other than SMC is used,
7. The applicable fluid is air. Consult SMC if the
1. This pressure switch is CE marked; however, it is
2. This pressure switch does not have an explosion
3. Do not use in an environment where static electri-
Back page 3
m/s
sor may not be damaged, the internal parts of the
sensor could be damaged and lead to a malfunction.
a greater pulling force on it can cause a malfunc-
tion. When handling, hold the body of the sen-
sor—do not dangle it from the cord.
when connecting the pipe to the switch. Exceeding
these values may cause the switch to malfunction.
and/or flammable gases or liquids.
in order to prevent application of torsional, tensile
or moment load to the tubes and fittings.
make sure that the tolerance of the tube's O.D.
satisfies the following specifications.
switch is to be used with other types of fluids.
a malfunction or erroneous switch output. Con-
nections should be done while the power is
turned off.
sor or its connector when the power is on. A
switch output malfunction may occur.
lines, avoiding wiring in the same conduit with
these lines. Malfunctions may occur due to noise
from these other lines.
sure that the F.G. terminal is grounded.
not equipped with surge protection against lightning.
Lightning surge countermeasures should be applied
directly to system components as necessary.
proof rating. Never use in the presence of an explo-
sive gas as this may cause a serious explosion.
city can cause problems, otherwise system failure
or malfunction may result.
1) Nylon tubing: ±0.1 mm or less
2) Soft nylon tubing: ±0.1 mm or less
3) Polyurethane tubing: +0.15 mm or less, –0.2 mm or less
Warning
Warning
Warning
2
) while handling. Although the body of the sen-
Operating Environment
Series
Specific Product Precautions 1
Be sure to read this before handling.
Refer to the back of pages 1 and 2 for Safety Instructions and “Precautions for
Handling Pneumatic Devices” (M-03-E3A) for Pressure Switches Precautions.
Connection
Handling
ZSE30A
(
F
)
/ISE30A
2. Mounting with brackets
1. Mounting and removing with panel mount adapter
• Cut the tube perpendicularly.
• Hold the tube and insert it into the one-touch fitting carefully
• Mount a bracket to the using two M3 x 5L mounting screws and
• When using bracket B, take piping dimensions into considera-
• To connect the connector, insert it straight while pinching the
• To remove the connector, pull it straight out while applying pres-
• Do not attempt to insert or pull the pressure sensor or its con-
and securely all the way to the bottom.
install on piping. The switch can be installed horizontally de-
pending on the installation location.
tion for installation.
To release push the claws
outward as shown on the pic-
ture, and pull back towards
lever, and then push the lever into the jack of the housing and
lock it.
sure with your thumb to the lever and unhooking it from the jack.
nector when the power is on. A switch output malfunction may
occur.
Caution
Panel mount
adapter
Connection/Removal of Connector
One-touch fitting
Lead wire (Blue)
Mounting screw
M3 x 5L
Bracket A
Panel
Mounting
Piping
Lever
Lead wire (Brown)
Bracket B
Tube
Claw
Mounting screw
M3 x 5L
Panel mount
adapter
The tightening
torque for bracket
mounting screw
should be 0.5 to
0.7 N·m.