TLE6286G Infineon Technologies, TLE6286G Datasheet
TLE6286G
Specifications of TLE6286G
TLE6286GNT
TLE6286GT
TLE6286GT
Available stocks
Related parts for TLE6286G
TLE6286G Summary of contents
Page 1
P r eli TLE 6286 ...
Page 2
... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...
Page 3
LIN-Transceiver with Voltage Regulator Features • Single-wire transceiver, suitable for LIN protocol • Transmission rate kBaud • Compatible to LIN specification 1.3, 2.0 • Compatible to ISO 9141 functions • Low current consumption in sleep mode • ...
Page 4
Figure 1 Pin Configuration (top view) Preliminary Data Sheet ...
Page 5
Pin Definitions and Functions Table 1 Pin No. Symbol Function GND Ground; place to cooling tabs to improve thermal behavior Reset delay; connected to ground with external delay capacitor 3 WD Watchdog; rising-edge triggered, ...
Page 6
Functional Block Diagram Output Stage 12 Bus Temperature Sensor Bandgap Reference Adjustment Figure 2 Block Diagram Preliminary Data Sheet Mode Control Driver Temp.- Protection Receiver TLE 4263 G Saturation Control ...
Page 7
Circuit Description The TLE 6286 is a single-wire transceiver combined with a LDO chip-by-chip integrated circuit in a P-DSO-16-11 package. It works as an interface between the protocol controller and the physical bus. The TLE 6286 is ...
Page 8
A wake-up caused by a message on the communication bus automatically enables the voltage regulator by switching the INHO output high. In parallel the wake-up is indicated by setting the RxD output low. When entering the normal mode this ...
Page 9
GND, reset is triggered at an output voltage of typ. 4. connected microcontroller will be monitored through the watchdog logic. In case of missing pulses at pin W, the reset output is set to ...
Page 10
Figure 4 Typical Reset Delay Timing vs. Delay Capacitance t The reset reaction time LOW after the output voltage has dropped below the reset threshold typically 1 s for delay capacitor of 47 nF. For other values for ...
Page 11
Figure 5 Typical Watchdog Trigger Time vs. Delay Capacitance Please note that in all calculations with capacitances, the leakage current of the capacitor is neglected! Preliminary Data Sheet ...
Page 12
Table 2 Absolute Maximum Ratings Parameter Voltages Supply voltage Battery supply voltage Bus input voltage Bus input voltage Logic voltages at ENLIN, TxD, RxD Input voltages at INHO Output current at INHO Reset output voltage Reset delay voltage V Output ...
Page 13
Table 3 Operating Range Parameter Supply voltage Battery Supply voltage Junction temperature Thermal Shutdown (junction temperature) Thermal shutdown temp. Thermal shutdown hyst. Thermal Resistances Junction ambient Preliminary Data Sheet Symbol Limit Values Min. Typ. V 4.5 – CCI V 6 ...
Page 14
Table 4 Electrical Characteristics 5 13.5V respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Current Consumption Current consumption at V (LIN + voltage BAT regulator) Current consumption V ...
Page 15
Table 4 Electrical Characteristics (cont’ 5 13.5V respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Inhibit Output (pin INHO) R Inhibit resistance ON Leakage current V V Output ...
Page 16
Table 4 Electrical Characteristics (cont’ 5 13.5V respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Watchdog (pin WD) Discharge current Upper timing threshold Lower timing threshold Watchdog trigger ...
Page 17
Table 4 Electrical Characteristics (cont’ 5 13.5V respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Bus Receiver Receiver threshold voltage, recessive to dominant edge Receiver threshold voltage, dominant ...
Page 18
Table 4 Electrical Characteristics (cont’ 5 13.5V respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Dynamic Transceiver Characteristics Falling edge slew rate Rising edge slew rate Slope symmetry ...
Page 19
Table 4 Electrical Characteristics (cont’ 5 13.5V respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Wake-up delay time Delay time for change sleep/stand by mode - normal mode ...
Page 20
Diagrams DRL Power-ON Over- Reset temperature Figure 6 Time Response, Watchdog with High-Frequency Clock ...
Page 21
µ ...
Page 22
µ ...
Page 23
Package Outlines 1.27 +0.1 0.41 -0.06 Index Marking 1) Does not include plastic or metal protrusion of 0.25 max. per side Figure 10 P-DSO-16-11 (Plastic Dual Small Outline) You can find all of our packages, sorts of packing and others ...