SYJ314-5MZ-M5 SMC Corporation, SYJ314-5MZ-M5 Datasheet - Page 57

• Manufacturer Part Number: SYJ314-5MZ-M5
• Description: Solenoid Valve; 3 port; normally closed; base mt; 24VDC; M plug conn w/.3 lead
• Manufacturer: SMC Corporation
• Type: Direct Operatedr

Specifications of SYJ314-5MZ-M5

• Brand/series: SY Series
• Configuration: 2-Position Single
• Number Of Ports: 3
• Primary Type: Solenoid Valve
• Voltage, Coil: 24 VDC

When making connections, take note that using other than the
supported size (ø3.5 to ø7) heavy-duty cord will not satisfy IP65
(enclosure) standards. Also, be sure to tighten the ground nut and
holding screw within their specified torque ranges.
Changing the entry direction
After separating the terminal block and housing, the cord entry
can be changed by attaching the housing in the desired direction
(4 directions at 90° intervals).
∗ When equipped with a light, be careful not to damage the light
Connection
1. Loosen the holding screw and pull the connector out of the
2. After removing the holding screw, insert a flat head screwdriv-
3. Loosen the terminal screws (slotted screws) on the terminal
4. Secure the cord by fastening the ground nut.
Grommet, L/M Plug Connector Type
With indicator light („Z)
DIN Terminal Type
With indicator light (DZ)
Note) Surge voltage suppressor other than diode has residual voltage
Note) Surge voltage suppressor of varistor has residual voltage
<For AC>
(There is no “S” type because the generation of surge voltage is
prevented by a rectifier.)
with the cord’s lead wires.
solenoid valve terminal block.
er, etc. into the notch on the bottom of the terminal block and
pry it open, separating the terminal block and the housing.
block, insert the cores of the lead wires into the terminals ac-
cording to the connection method, and fasten them securely
with the terminal screws.
Caution
Caution
Caution
corresponding to the protective element and rated voltage;
therefore protect the controller side from the surge. The residual
voltage of the diode is approximately 1 V.
corresponding to the protective element and rated voltage;
therefore, protect the controller side from the surge. The residual
voltage of the diode is approximately 1 V.
Surge Voltage Suppressor
How to Use DIN Terminal
Series
Specific Product Precautions 4
Be sure to read before handling.
SYJ300/500/700
NL: Neon bulb
Coil
Coil
With indicator light
Circuit Diagram with Indicator Light
Note) Refer to page 4-4-54 for DIN terminal (Y) conforming to DIN 43650C.
Compatible cable
Cord O.D.: ø3.5 to ø7
(Reference) 0.5 mm
Mount it so that there is no slippage or deformation in gaskets,
and tighten with the tightening torque as shown below.
Precautions
Plug in and pull out the connector vertically without tilting to one
side.
Without indicator light
SYJ300
SYJ500
SYJ700
Ground nut
tightening
torque
1.65 to 2.5 Nm
Rated voltage
Model
100 VAC
200 VAC
110 VAC
220 VAC
Caution
(Rating symbol)
Refer to table of DIN
connector part no. below.
Caution
Caution
24 VDC
12 VDC
Grommet (Rubber)
Washer
NL : Neon bulb
R : Resister
Terminal screw
(3 locations)
Tightening torque
0.2 to 0.25 Nm
AC circuit
Thread size
How to Use DIN Terminal
Solenoid Valve Mounting
M1.7
M2.5
DIN Terminal Part No.
M3
2
, 2 core or 3 core, equivalent to JIS C 3306
Voltage symbol
100V
200V
110V
220V
24V
12V
Tightening torque
0.12 Nm
0.45 Nm
0.8 Nm
SY100-61-1
LED : Light emitting diode
R
DC circuit
SY100-61-3-05
SY100-61-3-06
SY100-61-2-01
SY100-61-2-02
SY100-61-2-03
SY100-61-2-04
: Resister
Housing
Notch
Set screw
Tightening
torque
0.3 to 0.4 Nm
Terminal block
(Light mounting
location)
Part no.
4-4-59
V100
SY
SYJ
VK
VZ
VT
VP
VG
VP
S070
VQ
VKF
VQZ
VZ
VS
VFN