ISL83070EIBZA Intersil, ISL83070EIBZA Datasheet - Page 8

• Manufacturer Part Number: ISL83070EIBZA
• Description: IC TXRX RS485/422 3.3V ESD14SOIC
• Manufacturer: Intersil
• Type: Transceiverr

Specifications of ISL83070EIBZA

• Number Of Drivers/receivers: 1/1
• Protocol: RS422, RS485
• Voltage - Supply: 3 V ~ 3.6 V
• Mounting Type: Surface Mount
• Package / Case: 14-SOIC (3.9mm Width), 14-SOL
• Data Rate: 800Kbps
• Interface Circuit Standard 1: RS-422/RS-485
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Number Of Transceivers: 1
• Data Transmission Topology: Multidrop/Multipoint
• Receiver Signal Type: Differential
• Transmitter Signal Type: Differential
• Single Supply Voltage (typ): 3.3V
• Single Supply Voltage (min): 3V
• Single Supply Voltage (max): 3.6V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Power Supply Requirement: Single
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 14
• Package Type: SOIC N
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Electrical Specifications
NOTES:
10. Keep RE = VCC, and set the DE signal low time >600ns to ensure that the device enters SHDN.
12. Does not apply to the ISL83071E and ISL83077E.
13. Δt
14. ISL83070E - ISL83075E only.
15. V
16. Limits established by characterization and are not production tested.
17. If the Tx or Rx enable function isn’t needed, connect the enable pin to the appropriate supply (see “Pin Descriptions” table) through a 1kΩ to 3kΩ
18. Parts are 100% tested at +25°C. Full temperature limits are guaranteed by bench and tester characterization.
11. Set the RE signal high time >600ns to ensure that the device enters SHDN.
Test Circuits and Waveforms
ISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
Receiver Enable from Shutdown to
Output High
Receiver Enable from Shutdown to
Output Low
4. All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless otherwise
5. Supply current specification is valid for loaded drivers when DE = 0V.
6. Applies to peak current. See “Typical Performance Curves” for more information.
7. When testing devices with the shutdown feature, keep RE = 0 to prevent the device from entering SHDN.
8. When testing devices with the shutdown feature, the RE signal high time must be short enough (typically <100ns) to prevent the device from
9. Versions with a shutdown feature are put into shutdown by bringing RE high and DE low. If the inputs are in this state for less than 50ns, the parts
specified.
entering SHDN.
are guaranteed not to enter shutdown. If the inputs are in this state for at least 600ns, the parts are guaranteed to have entered shutdown. See
“Low Power Shutdown Mode” on page 11.
temperature, etc.). Only applies to the ISL83076E - 78E.
resistor.
CC
SKEW
V
CC
≥ 3.15V
PARAMETER
is the magnitude of the difference in propagation delays of the specified terminals of two units tested with identical test conditions (V
DE
DI
FIGURE 1A. V
D
Z
Y
8
OD
Test Conditions: V
Typicals are at V
V
OD
t
t
SYMBOL
ZH(SHDN)
ZL(SHDN)
AND V
OC
R
R
L
L
/2
/2
R
(Notes 9, 11, 12)
R
(Notes 9, 11, 12)
FIGURE 1. DC DRIVER TEST CIRCUITS
CC
L
L
CC
= 1kΩ, C
= 1kΩ, C
V
= 3.3V, T
OC
= 3.0V to 3.6V; Unless Otherwise Specified.
L
L
TEST CONDITIONS
= 15pF, SW = GND (Figure 6),
= 15pF, SW = V
A
= +25°C (Note 4).
V
CC
CC
(Figure 6),
DE
DI
FIGURE 1B. V
D
Z
Y
TEMP
(°C)
Full
Full
OD
WITH COMMON MODE LOAD
V
(Note 18)
OD
MIN
-
-
R
TYP
240
240
L
= 60Ω
(Note 18) UNITS
MAX
500
500
375Ω
375Ω
-7V TO +12V
June 22, 2007
FN6115.4
V
ns
ns
CM
CC
,