MIC3001GML Micrel Inc, MIC3001GML Datasheet - Page 64

• Manufacturer Part Number: MIC3001GML
• Description: IC FOM MANAGEMENT W/CALIBR 24MLF
• Manufacturer: Micrel Inc
• Type: Transceiverr

Specifications of MIC3001GML

• Protocol: SDHj Sonet
• Voltage - Supply: 3 V ~ 3.6 V
• Mounting Type: Surface Mount
• Package / Case: 24-MLF®, QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Drivers/receivers: -
• Other names: 576-1753-5; MIC3001GML

Micrel, Inc.
August 2004
Default Value
Serial Address
Byte Address
This register reflects (reads back) the value set in the APC register (APCSET0, APCSET1, or APCSET2 whichever is selected).
A valid OEM password is required for access to this register.
Default Value
Serial Address
Byte Address
This register reflects (reads back) the value set in the MODSET register. A valid OEM password is required for access to this
register.
Default Value
Serial Address
Byte Address
This register reflects (reads back) the status of the bits corresponding to the parameters defined below. A valid OEM password
is required for access to this register. Otherwise, reads are undefined and writes are ignored.
read only
read only
reserved
D[7]
D[6]
D[5]
D[4]
D[3]
D[2]
D[1]
D[0]
D[7]
D[7]
D[7]
Bit
TXFPOL
LUTSEL
LOSDIS
INTCAL
GPOD
GPOM
GPOC
TXFIN
read only
read only
reserved
D[6]
D[6]
D[6]
Function
RX power look-up table input
selection bit
TXFIN active polarity select; a fault
is indicated when TXFIN = TXFPOL
GPO output drive
GPO/RSOUT mode select
GPO output control
TXFIN mode select
RXLOS comparator disable
Calibration mode select
read only
read only
reserved
D[5]
D[5]
D[5]
Modulation DAC Setting (MODDAC)
OEM Readback Register (OEMRD)
BIAS DAC Setting (APCDAC)
0000 0000 b = 00 h
A6 h = 1010011 b
20 = 14 h
0000 0000 b = 00 h
A6 h = 1010011 b
21 = 15 h
0000 0000 b = 00 h
A6 h = 1010011 b
22 = 16 h
read only
read only
read only
Current VBIAS Setting
Current VMOD Setting
D[4]
D[4]
D[4]
INT
Operation
1 = RX power;
0 = temperature; read/write; ignored if INTCAL = 0.
0 = active-low;
1 = active-high; read/write; ignored if TXFIN = 0.
0 = open drain;
1 = push-pull; read/write; ignored if GPOM = 0.
0 = RSOUT; 1 = GPO; read/write.
0 = low; 1 = high; read/write; ignored if GPOM = 0.
0 = SHDN; 1 = TXFIN; read/write.
0 = enabled; 1 = disabled; read/write.
0 = external calibration;
1 = internal calibration; read/write.
64
read only
read only
read only
APCSAT
D[3]
D[3]
D[3]
read only
read only
read only
IBFLT
[e-mail]
D[2]
D[2]
D[2]
read only
read only
read only
TXFLT
D[1]
D[1]
D[1]
or [phone]
M9999-082404-A
read only
read only
read only
RSOUT
MIC3001
D[0]
D[0]
D[0]