DP-100NS-TRANSLUSCENT 3M, DP-100NS-TRANSLUSCENT Datasheet - Page 7

• Manufacturer Part Number: DP-100NS-TRANSLUSCENT
• Description: Adhesive; Epoxy; Translucent
• Manufacturer: 3M

Specifications of DP-100NS-TRANSLUSCENT

• Chemical Component: Amorphous Silica/Epoxy Resin
• Chemical System: Epoxy
• Color: Translucent
• Dispensing Method: Syringe
• Primary Type: Adhesive
• Time, Drying: Air Dry for 15 minutes, Force Dry for 10 minutes @ 66 °C +⁄- 5 °C (Aluminum Surface), If 3M™ Scotch-Weld™ Structural Primer 1945 B⁄A is Used, Apply a Thin Coating (0.5 mils) on the Metal Surfaces to be Bonded, Air Dry for 10 minutes, then Cure for 30 minu
• Time, Setting: 15 min. (Aluminum), 10 min. (Steel)
• Weight: 1.7 Oz.
• Lead Free Status / Rohs Status: RoHS Compliant part

8.2.2 Skin Protection
Avoid skin contact.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with
your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Polyethylene/Ethylene Vinyl Alcohol.
8.2.3 Respiratory Protection
Avoid breathing of vapors, mists or spray. Avoid breathing of dust created by cutting, sanding, grinding or machining.
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Half facepiece or fullface air-purifying respirator with P100 particulate filters, Half facepiece or fullface air-
purifying respirator with P95 particulate filters, Half facepiece or fullface air-purifying respirator with N95 particulate filters.
Consult the current 3M Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES
SOURCE OF EXPOSURE LIMIT DATA:
_________________________________________________________________________________________________
AMORPHOUS SILICA
3M MATERIAL SAFETY DATA SHEET Scotch-Weld(TM) Epoxy Adhesive DP-100 NS, Translucent (Part B)
Ingredient
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
Specific Physical Form:
Odor, Color, Grade:
General Physical Form:
Autoignition temperature
Flash Point
Flammable Limits - LEL
Flammable Limits - UEL
Boiling point
Density
Vapor Density
Vapor Pressure
Specific Gravity
pH
Melting point
Evaporation rate
Hazardous Air Pollutants
Volatile Organic Compounds
Percent volatile
VOC Less H2O & Exempt Solvents
CMRG
Authority
CEIL
Type
Viscous
light straw colored, epoxy odor
Liquid
No Data Available
>=240 ºC [Test Method: Estimated]
Not Applicable
Not Applicable
Not Applicable
1.18
Not Applicable
<=0.03 mmHg [@ 25 ºC]
1.18 [Ref Std: WATER=1]
Not Applicable
No Data Available
Not Applicable
0 % weight
0 % weight
0.00 % weight
0 g/l
5 mg/m3
Limit
Additional Information
Page 4 of 8