SI3452D-B01-GM Silicon Laboratories Inc, SI3452D-B01-GM Datasheet - Page 19

• Manufacturer Part Number: SI3452D-B01-GM
• Description: IC POE CONTROLLER MIDSPAN 40QFN
• Manufacturer: Silicon Laboratories Inc

Specifications of SI3452D-B01-GM

• Package / Case: 40-QFN
• Controller Type: Power over Ethernet Controller (POE)
• Interface: I²C
• Voltage - Supply: 3 V ~ 3.6 V
• Current - Supply: 14mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Maximum Power Dissipation: 1.2 W
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Product: Ethernet Controllers
• Standard Supported: IEEE 802.3at, IEEE 802.3af
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 3 V
• Supply Current (max): 14 mA
• Maximum Operating Temperature: + 85 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 336-1835-5

5.5. Command and Return Registers (Registers 0x12–0x1C)
The global command register enables manual port turn-on or turn-off, chip reset, port reset, and measurement of
port current and V
commands.
If the command results in a numerical return value, that value is stored in the measurement registers, which are
read-only. Each of the five possible measurements results in a 2 byte return value, and that value is stored in a
unique register. V
full scale is 6.5535 A.
The output data is updated by the proper command register write operation (see Table 23). This means that the
numerical value of the port current or V
command was issued. If the port turns off due to an overload or disconnect, the port current register contents will
not be set to zero. If a command to read port current is issued and the port is off, the return value will be zero.
5.6. Device Status Register (0x1D)
The device event bits are listed in Table 18.
The Device status register is RO. The V
or temperature is out of range and reset if the V
there is a change in the overtemp status (bit 6 of 0x1D), and bit 5 of the Interrupt register is set if there is a change
in the V
not clear the device status register.
In addition, bit B0 indicates whether or not detection back-off is used. For PSEs that are wired as Alternative B
(power on the spare pair–typically used for midspans), the time between detection pulses is increased to slightly
over two seconds to avoid interference with Alternative A (power on the data pair–typically used for endpoints). Bit
B0 can be toggled using the 0x10 command code.
B5—V
B6—OverTemp
EE
UVLO status (bit 5 of 0x1D). Reading register 0x1D clears these bits of the Interrupt register but does
Bit
EE
UVLO
EE
EE
is encoded in mV units; so, the full scale is 65.535 V. Iport is encoded in 100 µA units; so, the
. Register 0x12 is a Write only register. See Table 24 on page 24 for a list of all available
The Si3452 has per-port thermal shutdown sensors as well a global thermal shutdown
at a slightly higher temperature. The global thermal shutdown bit of the device event
register is set if this occurs.
V
EE
UVLO. The part is put in its reset state if V
EE
EE
Table 18. Device Status Bits
, UVLO, and overtemp bits reflect the device status. They are set if V
voltage in the measurement register will be the value at the time the
EE
or temperature is in range. Bit 6 of the Interrupt register is set if
Rev. 1.2
Description
EE
is not in a valid range.
Si3452
EE
19