KSZ8873MLL AM Micrel Inc, KSZ8873MLL AM Datasheet - Page 48
![IC ETHERNET SWITCH 3PORT 64-LQFP](/photos/6/81/68149/64-lqfp-micrel_sml.jpg)
KSZ8873MLL AM
Manufacturer Part Number
KSZ8873MLL AM
Description
IC ETHERNET SWITCH 3PORT 64-LQFP
Manufacturer
Micrel Inc
Specifications of KSZ8873MLL AM
Controller Type
Ethernet Switch Controller
Interface
MII
Voltage - Supply
1.8V, 2.5V, 3.3V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Supply
-
Lead Free Status / RoHS Status
Not Compliant, Lead free / RoHS Compliant
Other names
576-3633
KSZ8873MLL AM
KSZ8873MLLAM
KSZ8873MLL AM
KSZ8873MLLAM
Micrel, Inc.
PHY1 Register 29 (PHYAD = 0x1, REGAD = 0x1D): Not supported
PHY2 Register 29 (PHYAD = 0x2, REGAD = 0x1D): LinkMD Control/Status
PHY1 Register 31 (PHYAD = 0x1, REGAD = 0x1F): PHY Special Control/Status
PHY2 Register 31 (PHYAD = 0x2, REGAD = 0x1F): PHY Special Control/Status
September 2010
Bit
15
14-13
12
11-9
8-0
Bit
15-6
5
4
3
2
1
0
Vct_enable
Vct 10M Short
Reserved
Vct_fault_count
Name
Vct_result
Name
Reserved
Polrvs
MDI-X status
Force_lnk
Pwrsave
Remote
Loopback
Reserved
R/W
R/W
(SC)
RO
RO
RO
RO
R/W
RO
RO
RO
R/W
R/W
R/W
R/W
Description
Reserved
=1, Polarity is reversed
=0, Polarity is not reversed
=1, MDI-X
=0, MDI
=1, Force link pass
=0, Normal Operation
=0, Enable power saving
=1, Disable power saving
=1, Perform Remote loopback, as follows:
=0, Normal Operation
Reserved
Do not change the default value.
Description
=1, Enable cable diagnostic. After VCT
test has completed, this bit will be self-
cleared.
=0, Indicate cable diagnostic test (if
enabled) has completed and the status
information is valid for read.
=00, Normal condition
=01, Open condition detected in cable
=10, Short condition detected in cable
=11, Cable diagnostic test has failed
=1, Less than 10 meter short
Reserved
Distance to the fault.
It’s approximately
0.4m*vct_fault_count[8:0]
Port 1 (reg. 26, bit 1 = ‘1’)
Port 2 (reg. 42, bit 1 = ‘1’)
Start: RXP1/RXM1 (port 1)
Loopback: PMD/PMA of port 1’s PHY
End: TXP1/TXM1 (port 1)
Start: RXP2/RXM2 (port 2)
Loopback: PMD/PMA of port 2’s PHY
End: TXP2/TXM2 (port 2)
48
Default
0
00
0
000
{0, (0x00)}
Default
{(0x00),00}
0
0
0
1
0
0
Reference
Reg. 42, bit 4
Reg 42, bit[6:5]
Reg. 42, bit 7
{(Reg. 42, bit 0),
(Reg. 43, bit[7:0])}
Reference
Reg. 31, bit 5
Reg. 47, bit 5
Note: This bit is
only valid for 10BT
Reg. 30, bit 7
Reg. 46, bit 7
Reg. 26, bit 3
Reg. 42, bit 3
Reg. 26, bit 2
Reg. 42, bit 2
Reg. 26, bit 1
Reg. 42, bit 1
KSZ8873MLL/FLL/RLL
M9999-092309-1.2