PKM4113PI Ericsson Power Modules, PKM4113PI Datasheet - Page 45
![no-image](/images/manufacturer_photos/0/2/233/ericsson_power_modules_sml.jpg)
PKM4113PI
Manufacturer Part Number
PKM4113PI
Description
DC/DC Converters & Regulators 12 Vdc 10.5A Iso Input 36-75V 126W
Manufacturer
Ericsson Power Modules
Series
PKMr
Datasheet
1.PKM4618API.pdf
(50 pages)
Specifications of PKM4113PI
Product
Isolated
Output Power
126 W
Input Voltage Range
36 V to 75 V
Number Of Outputs
1
Output Voltage (channel 1)
12 V
Output Current (channel 1)
10.5 A
Isolation Voltage
1.5 KV
Package / Case Size
Quarter Brick
Output Type
Isolated
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PKM4113PI
Manufacturer:
ERICSSON
Quantity:
38
Part Number:
PKM4113PI
Manufacturer:
ERICSSON/爱立信
Quantity:
20 000
Company:
Part Number:
PKM4113PILA
Manufacturer:
ERICSSON
Quantity:
530
Part Number:
PKM4113PILA
Manufacturer:
ERICSSON/爱立信
Quantity:
20 000
Company:
Part Number:
PKM4113PILA2
Manufacturer:
ERICSSON
Quantity:
134
Part Number:
PKM4113PILA2
Manufacturer:
ERICSSON/爱立信
Quantity:
20 000
Company:
Part Number:
PKM4113PIP
Manufacturer:
VICOR
Quantity:
726
Part Number:
PKM4113PIP
Manufacturer:
ERICSSON/爱立信
Quantity:
20 000
Operating information
Input Voltage
The input voltage range 36 to 75Vdc meets the requirements
of the European Telecom Standard ETS 300 132-2 for normal
input voltage range in —48 and —60 Vdc systems,
-40.5 to -57.0 V and —50.0 to -72 V respectively.
At input voltages exceeding 75 V, the power loss will be
higher than at normal input voltage and T
absolute max +100°C. The absolute maximum continuous
input voltage is 80Vdc.
Turn-off Input Voltage
The DC/DC converters monitor the input
voltage and will turn on and turn off at predetermined levels.
The minimum hysteresis between turn on and turn off input
voltage is 1V.
Remote Control (RC)
The maximum required sink current is 1 mA. When the RC pin
is left open, the voltage generated on the RC pin is
3.0 — 6.5 V.
The second option is “positive logic” remote control, which
can be ordered by adding the suffix “P” to the end of the part
number. The converter will turn on when the input voltage
is applied with the RC pin open. Turn off is achieved by
connecting the RC pin to the - In. To ensure safe turn off the
voltage difference between RC pin and the - In pin shall be
less than 1V. The converter will restart automatically when
this connection is opened.
Input and Output Impedance
The impedance of both the input source and the load will
interact with the impedance of the DC/DC converter. It is
important that the input source has low characteristic
impedance. The converters are designed for stable operation
without external capacitors connected to the input or output.
The performance in some applications can be enhanced by
addition of external capacitance as described under External
Decoupling Capacitors. If the input voltage source contains
significant inductance, the addition of a 100 μF capacitor
across the input of the converter will ensure stable operation.
The capacitor is not required when powering the DC/DC
Prepared (also subject responsible if other)
ESECZHW
Approved
SEC/D (Linda Zhong)
PKM 4000 PI series
DC/DC converters, Input 36-75 V, Output 35 A/126 W
The products are fitted with a
remote control function referenced
to the primary negative input
connection (- In), with negative and
positive logic options available. The
RC function allows the converter to
be turned on/off by an external
device like a semiconductor or
mechanical switch.
ref
must be limited to
Checked
MICJOHN
PRODUCT SPECIFICATION
No.
3/1301-BMR631
Date
2006-02-22
converter from an input source with an inductance below
10 μH.
External Decoupling Capacitors
When powering loads with significant dynamic current
requirements, the voltage regulation at the point of load can
be improved by addition of decoupling capacitors at the load.
The most effective technique is to locate low ESR ceramic
and electrolytic capacitors as close to the load as possible,
using several parallel capacitors to lower the effective ESR.
The ceramic capacitors will handle high-frequency dynamic
load changes while the electrolytic capacitors are used to
handle low frequency dynamic load changes. Ceramic
capacitors will also reduce any high frequency noise at the
load.
It is equally important to use low resistance and low
inductance PCB layouts and cabling.
External decoupling capacitors will become part of the
control loop of the DC/DC converter and may affect the
stability margins. As a “rule of thumb”, 100 μF/A of output
current can be added without any additional analysis. The
ESR of the capacitors is a very important parameter. Power
Modules guarantee stable operation with a verified ESR value
of >10 mΩ across the output connections.
For further information please contact your local Ericsson
Power Modules representative.
Output Voltage Adjust (V
The DC/DC converters have an Output Voltage Adjust pin
(V
or below Output voltage initial setting.
When increasing the output voltage, the voltage at the output
pins (including any remote sense compensation ) must be
kept below the threshold of the over voltage protection, (OVP)
to prevent the converter from shutting down. At increased
output voltages the maximum power rating of the converter
remains the same, and the max output current must be
decreased correspondingly.
To increase the voltage the resistor should be connected
between the V
Output voltage adjust function is according to information
given under the Output section for the respective product.
To decrease the output voltage, the resistor should be
connected between the V
adj
). This pin can be used to adjust the output voltage above
adj
pin and +Sense pin. The resistor value of the
Technical Specifi cation
EN/LZT 146 310 R1B Nov 2006
© Ericsson Power Modules AB
Rev
B
adj
adj
pin and —Sense pin.
)
Reference
3 (6)
45