CY8C20110-LDX2I Cypress Semiconductor Corp, CY8C20110-LDX2I Datasheet - Page 8
![IC CAPSENSE EXP 10 I/O 16UQFN](/photos/6/81/68142/cy8c20110-ldx2i_sml.jpg)
CY8C20110-LDX2I
Manufacturer Part Number
CY8C20110-LDX2I
Description
IC CAPSENSE EXP 10 I/O 16UQFN
Manufacturer
Cypress Semiconductor Corp
Series
CapSense Express™ CY8C20xxxr
Datasheet
1.CY8C20160-SX2I.pdf
(39 pages)
Specifications of CY8C20110-LDX2I
Package / Case
16-UQFN, 16-µQFN
Controller Type
Capacitive Sensing Controller
Interface
I²C
Voltage - Supply
2.4 V ~ 5.25 V
Current - Supply
1.5mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Processor Series
CY8C201xx
Core
M8C
Data Bus Width
8 bit
Interface Type
I2C
Number Of Programmable I/os
10
Operating Supply Voltage
2.4 V to 5.25 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Development Tools By Supplier
CY3218-CAPEXP1
Minimum Operating Temperature
- 40 C
Program Memory Type
Flash
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
428-2043 - KIT CAPSENSE EXPRESS CY8C20110770-1000 - ISP 4PORT FOR CYPRESS PSOC MCU
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
428-2046
I
The CapSense Express devices support the industry standard I
■
■
■
■
The I
I
The device uses a seven bit addressing protocol. The I
the first 7 bits contain the address and the LSB indicates the data transfer direction. Zero in the LSB bit indicates the write transaction
from master and one indicates read transfer by the master. The following table shows examples for different I
Table 4. I
I
‘Clock stretching’ or ‘bus stalling’ in I
is a state in which the slave holds the SCL line low to indicate
that it is busy. In this condition, the master is expected to wait till
the SCL is released by the slave.
When an I
device, the CapSense Express stalls the I
reception of each byte (that is, just before the ACK/NAK bit) until
processing of the byte is complete and critical internal functions
are executed. Use a fully I
with the CapSense Express device.
Document Number: 001-54606 Rev. *E
2
2
2
C Device Addressing
C Clock Stretching
Configuring the device
Reading the status and data registers of the device
Controlling device operation
Executing commands
C Interface
7-bit Slave
Address
2
C address can be modified during configuration.
75
75
1
1
2
2
C master communicates with the CapSense Express
C Address Examples
D7
0
0
1
1
2
C compliant master to communicate
D6
0
0
0
0
2
C communication protocol
D5
0
0
0
0
2
C bus after the
D4
0
0
1
1
D3
0
0
0
0
2
C data transfer is always initiated by the master sending a one byte address:
D2
0
0
1
1
2
C protocol, which can be used for:
If the I
software I
of time (as specified in
page 9) for each register write and read operation before the next
bit is transmitted. The I
should be high) before the I
with CapSense Express. If the master fails to do so and
continues to communicate, the communication is erroneous.
The following diagrams represent the ACK time delays shown in
“Format for Register Write and Read”
read.
D1
1
1
1
1
2
C master does not support clock stretching (a bit banged
0(W)
0(W)
1(W)
1(R)
2
D0
C Master), the master must wait for a specific amount
CY8C20160, CY8C20140
CY8C20110, CY8C20180
“Format for Register Write and Read”
2
C master must check the SCL status (it
2
C master initiates any data transfer
8-bit Slave Address
02
03
96
97
on page 9 for write and
2
C addresses.
CY8C20142
Page 8 of 39
on
[+] Feedback