ENC28J60-I/SP Microchip Technology, ENC28J60-I/SP Datasheet - Page 66
![IC ETHERNET CTRLR W/SPI 28DIP](/photos/6/59/65908/150-28-dip_sml.jpg)
ENC28J60-I/SP
Manufacturer Part Number
ENC28J60-I/SP
Description
IC ETHERNET CTRLR W/SPI 28DIP
Manufacturer
Microchip Technology
Specifications of ENC28J60-I/SP
Package / Case
28-DIP (0.300", 7.62mm)
Controller Type
Ethernet Controller, MAC/10Base-T
Interface
SPI
Voltage - Supply
3.1 V ~ 3.6 V
Current - Supply
160mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Through Hole
Input Voltage Range (max)
5.5 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
Through Hole
Operating Supply Voltage
3.1 V to 3.6 V
Supply Current (max)
180 mA
Product
Ethernet Controllers
Standard Supported
IEEE 802.3
Data Rate
10 Mbps
Ethernet Connection Type
10Base-T
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
DM163024 - BOARD DEMO PICDEM.NET 2AC164123 - BOARD DAUGHTER ETH PICTAIL PLUSAC164121 - BOARD DAUGHTER PICTAIL ETHERNET
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ENC28J60-I/SP
Manufacturer:
MICROCHIP
Quantity:
6 500
ENC28J60
12.1
The INT Interrupt Enable bit (INTIE) is a global enable
bit which allows the following interrupts to drive the INT
pin:
• Receive Error Interrupt (RXERIF)
• Transmit Error Interrupt (TXERIF)
• Transmit Interrupt (TXIF)
• Link Change Interrupt (LINKIF)
• DMA Interrupt (DMAIF)
• Receive Packet Pending Interrupt (PKTIF)
REGISTER 12-1:
DS39662B-page 64
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
R-0
INT
INT Interrupt Enable (INTIE)
INT: INT Interrupt Flag bit
1 = INT interrupt is pending
0 = No INT interrupt is pending
BUFER: Ethernet Buffer Error Status bit
1 = An Ethernet read or write has generated a buffer error (overrun or underrun)
0 = No buffer error has occurred
Reserved: Read as ‘0’
LATECOL: Late Collision Error bit
1 = A collision occurred after 64 bytes had been transmitted
0 = No collisions after 64 bytes have occurred
Unimplemented: Read as ‘0’
RXBUSY: Receive Busy bit
1 = Receive logic is receiving a data packet
0 = Receive logic is Idle
TXABRT: Transmit Abort Error bit
1 = The transmit request was aborted
0 = No transmit abort error
CLKRDY: Clock Ready bit
1 = OST has expired; PHY is ready
0 = OST is still counting; PHY is not ready
BUFER
R/C-0
ESTAT: ETHERNET STATUS REGISTER
C = Clearable bit
‘1’ = Bit is set
R-0
r
LATECOL
R/C-0
Preliminary
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
When any of the above interrupts are enabled and
generated, the virtual bit, INT in the ESTAT register
(Register 12-1), will be set to ‘1’. If EIE.INTIE is ‘1’, the
INT pin will be driven low.
12.1.1
The registers associated with the INT interrupts are
shown in Register 12-2, Register 12-3, Register 12-4
and Register 12-5.
U-0
—
INT INTERRUPT REGISTERS
RXBUSY
R-0
© 2006 Microchip Technology Inc.
x = Bit is unknown
TXABRT
R/C-0
CLKRDY
R/W-0
bit 0