MPC8358EZQAGDGA Freescale Semiconductor, MPC8358EZQAGDGA Datasheet - Page 74

• Manufacturer Part Number: MPC8358EZQAGDGA
• Description: MPU POWERQUICC II PRO 668-PBGA
• Manufacturer: Freescale Semiconductor

Specifications of MPC8358EZQAGDGA

• Processor Type: MPC83xx PowerQUICC II Pro 32-Bit
• Speed: 400MHz
• Voltage: 1.2V
• Mounting Type: Surface Mount
• Package / Case: 668-PBGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Features: -

Clocking
input selects whether CLKIN or CLKIN/2 is driven out on the PCI_SYNC_OUT signal. The
OCCR[PCIOENn] parameters enable the PCI_CLK_OUTn, respectively.
PCI_SYNC_OUT is connected externally to PCI_SYNC_IN to allow the internal clock subystem to
synchronize to the system PCI clocks. PCI_SYNC_OUT must be connected properly to PCI_SYNC_IN,
with equal delay to all PCI agent devices in the system, to allow the device to function. When the device
is configured as a PCI agent device, PCI_CLK is the primary input clock. When the device is configured
as a PCI agent device the CLKIN and the CFG_CLKIN_DIV signals should be tied to GND.
When the device is configured as a PCI host device (RCWH[PCIHOST] = 1) and PCI clock output is
disabled (RCWH[PCICKDRV] = 0), clock distribution and balancing done externally on the board.
Therefore, PCI_SYNC_IN is the primary input clock.
As shown in
phase-locked loop (PLL), the system PLL, and the clock unit to create the QUICC Engine clock (ce_clk),
the coherent system bus clock (csb_clk), the internal DDRC1 controller clock (ddr1_clk), and the internal
clock for the local bus interface unit and DDR2 memory controller (lb_clk).
The csb_clk frequency is derived from a complex set of factors that can be simplified into the following
equation:
In PCI host mode, PCI_SYNC_IN × (1 + CFG_CLKIN_DIV) is the CLKIN frequency; in PCI agent
mode, CFG_CLKIN_DIV must be pulled down (low), so PCI_SYNC_IN × (1 + CFG_CLKIN_DIV) is
the PCI_CLK frequency.
The csb_clk serves as the clock input to the e300 core. A second PLL inside the e300 core multiplies up
the csb_clk frequency to create the internal clock for the e300 core (core_clk). The system and core PLL
multipliers are selected by the SPMF and COREPLL fields in the reset configuration word low (RCWL)
which is loaded at power-on reset or by one of the hard-coded reset options. See Chapter 4, “Reset,
Clocking, and Initialization,” in the MPC8360E PowerQUICC II Pro Integrated Communications
Processor Family Reference Manual for more information on the clock subsystem.
The ce_clk frequency is determined by the QUICC Engine PLL multiplication factor (RCWL[CEPMF)
and the QUICC Engine PLL division factor (RCWL[CEPDF]) according to the following equation:
The internal ddr1_clk frequency is determined by the following equation:
Note that the lb_clk clock frequency (for DDRC2) is determined by RCWL[LBCM]. The internal
ddr1_clk frequency is not the external memory bus frequency; ddr1_clk passes through the DDRC1 clock
divider (÷2) to create the differential DDRC1 memory bus clock outputs (MEMC1_MCK and
MEMC1_MCK). However, the data rate is the same frequency as ddr1_clk.
The internal lb_clk frequency is determined by the following equation:
74
csb_clk = {PCI_SYNC_IN × (1 + CFG_CLKIN_DIV)} × SPMF
ce_clk = (primary clock input × CEPMF) ÷ (1 + CEPDF)
ddr1_clk = csb_clk × (1 + RCWL[DDR1CM])
lb_clk = csb_clk × (1 + RCWL[LBCM])
MPC8358E PowerQUICC II Pro Processor Revision 2.1 PBGA Silicon Hardware Specifications, Rev. 3
Figure
53, the primary clock input (frequency) is multiplied by the QUICC Engine block
Freescale Semiconductor