Z8L18220ASC Zilog, Z8L18220ASC Datasheet - Page 67
![IC 20MHZ STATIC MIMIC 100-LQFP](/photos/6/76/67664/269-100-lqfp_sml.jpg)
Z8L18220ASC
Manufacturer Part Number
Z8L18220ASC
Description
IC 20MHZ STATIC MIMIC 100-LQFP
Manufacturer
Zilog
Datasheet
1.Z8018233FSG.pdf
(109 pages)
Specifications of Z8L18220ASC
Processor Type
Z180
Features
Smart Peripheral Controller
Speed
20MHz
Voltage
3.3V
Mounting Type
Surface Mount
Package / Case
100-LQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
DS971820600
Bit 0 16450 MIMIC Mode Enable
(Reset value=0) This bit = 1 will force the mimic into 16450
mode. Bit 0 in the FCR reg is forced to zero as well as the
mimic internal FIFO enable. When used, this bit should be
programmed at MIMIC initialization and not modified
afterwards.
This register contains an 8-bit constant for emulation of the
16550 four character timeout feature. Software must
determine the value to load into this register based on the
bit rate and word length specified by the MIMIC interface
with the PC. This timer receives its input from the /TRxCB
Clock of the ESCC. This timer is enabled to down count
when the enable bit in the FSR register is set and the trigger
level interrupt has not been activated on the RCVR FIFO.
The counter reloads and counts down each time there is
a read or write to the RCVR FIFO.
The receive timeout timer is enhanced to emulate the
actual 16550 when bit 1 of the FIFO status and control
register is enabled. Under most circumstances, this register
should be programmed for four character timers (40d,
8-N-1).
Zilog
D7 D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0
1
1
Figure 66. Transmit Timeout Timer Constant
1
Figure 65. Receive Timeout Timer Constant
1
(Z180 MPU Read/Write, Address xxEBH)
(Z180 MPU Read/Write, Address xxEAH)
1
1
1
1
1
1
1
1
1
1
1
1
Rec Timeout Constant
Transmitter Time Constant
P R E L I M I N A R Y
PS009801-0301
This register contains an 8-bit constant for determining the
interval for the Transmit Timeout Timer. If allowed to
decrement to zero, this timer interrupts the MPU by setting
the THR bit in the IUS/IP register. This timer receives its
input from the /TRxCB Clock of the SCC. The timer is
enabled to down count when the enable bit in the FSR
register is set and the trigger level has not been reached
on the XMIT FIFO. The counter reloads each time there is
a read or write to the XMIT FIFO.
Transmit And Receive Timers
Because of the speed at which data transfers can take
place between the Z180
timers have been added to alleviate any software problems
that a high speed parallel data transfer might cause. These
timers allow the programmer to slow down the data transfer
just as if the 16550 MIMIC interface had to shift the data in
and out serially. The Timers receive their input from the
/TRxCB Clock since, in 16550 MIMIC mode, the ESCC
channel B is disabled. For example, the clock source for
the 8-bit registers: RTTC (Receive Timeout Time Constant,
xxEAH), TTTC (Transmit Timeout Time Constant, xxEBH),
TTCR (Transmit Time Constant Register, xxFAH) and
RTCR (Receive Time Constant Register, xxFBH) uses the
/TRxCB Clock output. The /TRxCB Clock output needs to
be generated by the ESCC’s channel B's 16-bit BRG as its
clock source, thus allowing the programmer to access a
total of 24 bits as a timer to slow down the data transfer.
In most cases, ESCC Ch. B BRG should be programmed
to output at a frequency equivalent to the desired serial
transfer rate. The output of the BRG should be routed to the
/TRxCB pin.
Figure 67. Transmitter Time Constant Register
D7 D6 D5 D4 D3 D2 D1 D0
1
(Z180 MPU Read/Write, Address xxFAH)
1
1
1
1
1
™
1
MPU and the PC/XT/AT, two
1
Z
XMIT Timeout Constant
ILOG
I
NTELLIGENT
Z80182/Z8L182
P
ERIPHERAL
3-67