ADSP-21061LAS-176 Analog Devices Inc, ADSP-21061LAS-176 Datasheet - Page 35

• Manufacturer Part Number: ADSP-21061LAS-176
• Description: IC DSP CONTROLLER 32BIT 240MQFP
• Manufacturer: Analog Devices Inc
• Series: SHARC®r
• Type: Floating Pointr

Specifications of ADSP-21061LAS-176

• Rohs Status: RoHS non-compliant
• Interface: Synchronous Serial Port (SSP)
• Clock Rate: 44MHz
• Non-volatile Memory: External
• On-chip Ram: 128kB
• Voltage - I/o: 3.30V
• Voltage - Core: 3.30V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 240-MQFP, 240-PQFP
• Device Core Size: 32b
• Architecture: Super Harvard
• Format: Floating Point
• Clock Freq (max): 44MHz
• Mips: 44
• Device Input Clock Speed: 44MHz
• Ram Size: 128KB
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (min): 3.15V
• Operating Supply Voltage (max): 3.45V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 240
• Package Type: MQFP
• Lead Free Status / Rohs Status: Not Compliant

Three-State Timing—Bus Master, Bus Slave, HBR, SBTS
These specifications show how the memory interface is disabled
(stops driving) or enabled (resumes driving) relative to CLKIN
and the SBTS pin. This timing is applicable to bus master transi-
tion cycles (BTC) and host transition cycles (HTC) as well as the
SBTS pin.
Table 19. Three-State Timing—Bus Master, Bus Slave
1
2
3
Parameter
Timing Requirements
t
t
Switching Characteristics
t
t
t
t
t
t
t
t
t
t
t
t
t
t
Strobes = RD, WR, PAGE, DMAGx, MSx, BMS, SW.
In addition to bus master transition cycles, these specs also apply to bus master and bus slave synchronous read/write.
Memory Interface = Address, RD, WR, MSx, SW, PAGE, DMAGx, and BMS (in EPROM boot mode).
STSCK
HTSCK
MIENA
MIENS
MIENHG
MITRA
MITRS
MITRHG
DATEN
DATTR
ACKEN
ACKTR
ADCEN
ADCTR
MTRHBG
MENHBG
SBTS Setup Before CLKIN
SBTS Hold Before CLKIN
Address/Select Enable After CLKIN
Strobes Enable After CLKIN
HBG Enable After CLKIN
Address/Select Disable After CLKIN
Strobes Disable After CLKIN
HBG Disable After CLKIN
Data Enable After CLKIN
Data Disable After CLKIN
ACK Enable After CLKIN
ACK Disable After CLKIN
ADRCLK Enable After CLKIN
ADRCLK Disable After CLKIN
Memory Interface Disable Before HBG Low
Memory Interface Enable After HBG High
INTERFACE
MEMORY
CLKOUT
CLKIN
DATA
SBTS
ACK
Figure 21. Three-State Timing (Bus Transition Cycle, SBTS Assertion)
2
2
2
2
1
1
t
ADCEN
t
t
ACKEN
MIENA,
t
DATEN
Rev. C | Page 35 of 56 | July 2007
t
MIENS,
3
t
3
MIENHG
t
STSCK
t
HTSCK
t
Min
12 + DT/2
–1 – DT/8
–1.5 – DT/8
–1.5 – DT/8
9 + 5DT/16
0 – DT/8
7.5 + DT/4
–1 – DT/8
–2 – DT/8
0 + DT/8
19 + DT
t
DATTR
ACKTR
t
ADSP-21061/ADSP-21061L
t
ADCTR
MITRA,
t
MITRS,
5 V and 3.3 V
t
MITRHG
Max
6 + DT/2
0 – DT/4
1.5 – DT/4
2.0 – DT/4
7 – DT/8
6 – DT/8
8 – DT/4
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns