AD1953YSTRL7 Analog Devices Inc, AD1953YSTRL7 Datasheet - Page 21

• Manufacturer Part Number: AD1953YSTRL7
• Description: IC DSP DAC AUDIO3CH/26BIT 48LQFP
• Manufacturer: Analog Devices Inc
• Series: SigmaDSP®r

Specifications of AD1953YSTRL7

• Rohs Status: RoHS non-compliant
• Number Of Bits: 26
• Data Interface: Serial
• Number Of Converters: 3
• Voltage Supply Source: Analog and Digital
• Power Dissipation (max): 540mW
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 48-LQFP
• For Use With: EVAL-AD1953EBZ - BOARD EVAL FOR AD1953 3CH 24BIT
• Settling Time: -

Control Register 1
Control Register 1 is a 14-bit register that controls data capture
modes, serial modes, de-emphasis, mute, power-down, and
SPI-to-memory transfers. Table III documents the contents of
this register. Table IV details the two bits in the register’s
read operation.
Bits <1:0> set the wordlength, which is used in right-justified
serial modes to determine where the MSB is located relative to
the start of the audio frame.
Bits <3:2> select one of four serial modes, which are discussed
in the Serial Data Input Port section.
The de-emphasis curve selection Bits <5:4> turn on the internal
de-emphasis filter for one of three possible sample rates.
Bit <6>, the soft power-down bit, stops the internal clocks to
the DSP core, but does not reset the part. The digital power
consumption is reduced to a low level when this bit is asserted.
Reset can only be asserted using the external reset pin.
Soft mute (Bit <7>) is used to initiate a volume ramp-down
sequence. If the initial volume was set to 1.0, this operation will
take 512 audio frames to complete. When this bit is deasserted,
a ramp-up sequence is initiated until the volume returns to its
original setting.
The initiate-safe-transfer Bit <9> will request a data transfer
from the SPI safeload registers to the parameter RAM. The
safeload registers contain address-data pairs, and only those
registers that have been written to since the last transfer opera-
tion will be uploaded. The user may poll for this operation being
complete by reading Bit <0> of Control Register 1. The Safeload
Mechanism section goes into more detail on this feature.
Bit <10>, the halt program bit, is used to initiate a volume
ramp-down followed by a shutdown of the DSP core. The user
may poll for this operation being complete by reading Bit <1>
of Control Register 1.
The Data Capture Serial Out mode is controlled with Bits
<13:12>. This function can be used to send data that is cap-
tured using the data-capture feature to external devices such as
an external stereo DAC or multichannel codec. The Data Cap-
ture Registers and Outputs section gives more information about
the TDM and data capture features.
REV. 0
–21–
Register Bits
13:12
11
10
9
8
7
6
5:4
3:2
1:0
Table III. Control Register 1 Write Definition
Function
Data Capture Serial Out Mode Control
00 = none
01 = TDM 6-channel out, uses Pins 41–43
10 = 2-channel out, uses Pin 45
11 = Unused
Unused
Halt Program (1 = Halt)
Initiate Safe Transfer (1 = Transfer)
Unused
Soft Mute (1 = Start Mute Sequence)
Soft Power-Down (1 = Power Down)
De-emphasis Curve Select
00 = none
01 = 44.1 kHz
10 = 32 kHz
11 = 48 kHz
Serial In Mode
00 = I
01 = Right-Justified
10 = DSP
11 = Left-Justified
Word Length
00 = 24 Bits
01 = 20 Bits
10 = 16 Bits
11 = 16 Bits
2
S
AD1953