CE JMK316 BJ106KD-T Taiyo Yuden, CE JMK316 BJ106KD-T Datasheet - Page 33
![no-image](/images/manufacturer_photos/0/6/649/taiyo_yuden_sml.jpg)
CE JMK316 BJ106KD-T
Manufacturer Part Number
CE JMK316 BJ106KD-T
Description
Cap Ceramic 10uF 6.3VDC X5R 10% SMD 1206 T/R
Manufacturer
Taiyo Yuden
Type
Flatr
Datasheet
1.CE_EMK107_BJ105KA-T.pdf
(51 pages)
Specifications of CE JMK316 BJ106KD-T
Package/case
1206
Mounting
Surface Mount
Capacitance Value
10 uF
Dielectric
X5R
Tolerance
10 %
Voltage
6.3 Vdc
Product Length
3.2 mm
Product Height
0.85 mm
Product Depth
1.6 mm
【Test Methods and Remarks】
【Test Methods and Remarks】
【Test Methods and Remarks】
【Test Methods and Remarks】
【Test Methods and Remarks】
■
* This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
mlcc06_reli_e-01
12. Resistance to Soldering
Specified Value
13. Temperature Cycle ( Thermal Shock)
Specified Value
Preconditioning:Thermal treatment (at 150℃ for 1hr) Note1
Conditions for 1 cycle/ Step 1: Minimum operating temperature
14. Humidity ( Steady state)
Specified Value
15. Humidity Loading
Specified Value
16. High Temperature Loading
Specified Value
Note1
Note2
Note3
Preconditioning:Thermal treatment (at 150℃ for 1hr) Note1
Solder temperature:270±5℃
Duration:3±0.5sec.
Preheating conditions: 80 to 100℃, 2 to 5 min.
Recovery : 24±2hrs under the standard condition
Number of cycles:5 times
Recovery : 24±2hrs under the standard condition
Preconditioning:Thermal treatment (at 150℃ for 1hr) Note1
Temperature:40±2℃
Humidity:90 to 95%RH
Duration: 500
Recovery : 24±2hrs under the standard condition
According to JIS 5102 clause 9.9.
Preconditioning:Voltage treatment
Temperature:40±2℃
Humidity:90 to 95%RH
Applied voltage:Rated voltage
Charge/discharge current:50mA max.
Duration: 500
Recovery : 24±2hrs under the standard condition
According to JIS 5102 clause 9.10.
Preconditioning:Voltage treatment
Temperature:125±3℃ (B7, C7) , 85±2℃ (BJ)
Applied voltage:Rated voltage×2 ( HMK)
Charge/discharge current:50mA max.
Duration: 1000
Recovery : 24±2hrs under the standard condition
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
RELIABILITY DATA
Thermal treatment : Initial value shall be measured after test sample is heat-treated at 150+0/-10℃ for an hour and kept at room temperature for 24±2hours.
Voltage treatment : Initial value shall be measured after test sample is voltage-treated for an hour at both the temperature and voltage specified in the test conditions, and
Standard condition: Temperature: 5 to 35℃, Relative humidity: 45 to 85 % RH, Air pressure: 86 to 106kPa
+24
-0
+24
-0
+24
-0
Rated voltage×1.5 ( QMK)
Rated voltage×1.2 ( SMK)
hrs
hrs
hrs
150 to 200℃, 2 to 5min.
Step 2: Normal temperature
Step 3: Maximum operating temperature
Step 4: Normal temperature
kept at room temperature for 24±2hours.
When there are questions concerning measurement results, in order to provide correlation data, the test shall be conducted under the following condi-
tion.
Temperature: 20±2℃,
Unless otherwise specified, all the tests are conducted under the "standard condition".
Note2
Note2
Note3
Note3
Note3
Note3
Note3
Relative humidity: 60 to 70 % RH, Air pressure: 86 to 106kPa
Appearance:
Capacitance change:
Dissipation factor :
Insulation resistance:
Withstanding voltage ( between terminals) : No abnormality
Appearance:
Capacitance change: Within±15% (HMK) , ±7.5% (QMK, SMK)
Dissipation factor:
Insulation resistance: Initial value
Appearance:
Capacitance change: Within±15%
Dissipation factor :
Insulation resistance: 25MΩ μF or 1000MΩ, whichever is smaller.
Appearance:
Capacitance change: Within±15%
Dissipation factor:
Insulation resistance: 10MΩ μF or 500MΩ, whichever is smaller.
Appearance:
Capacitance change: Within±15%
Dissipation factor:
Insulation resistance: 50MΩ μF or 1000MΩ, whichever is smaller.
+0
-3
+0
-3
℃ 30±3min.
℃ 30±3min.
2 to 3min.
2 to 3min.
No abnormality
7%max ( HMK) , 5%max ( QMK, SMK) .
No abnormality
Initial value
No abnormality
7%max ( HMK) , 5%max ( QMK, SMK) .
No abnormality
7%max ( HMK) , 5%max ( QMK, SMK) .
1 1
No abnormality
Within±15% (HMK) , ±10% (QMK, SMK)
Initial value
Initial value
mlcc06_reli-R2