AD7541AKR Analog Devices Inc, AD7541AKR Datasheet - Page 6

• Manufacturer Part Number: AD7541AKR
• Description: IC DAC 12BIT MULT MONO 18-SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD7541AKR

• Rohs Status: RoHS non-compliant
• Settling Time: 600ns
• Number Of Bits: 12
• Data Interface: Parallel
• Number Of Converters: 1
• Voltage Supply Source: Single Supply
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 18-SOIC (7.5mm Width)
• Power Dissipation (max): -

AD7541A
APPLICATIONS HINTS
Output Offset: CMOS D/A converters exhibit a code-dependent
output resistance which in turn can cause a code-dependent
error voltage at the output of the amplifier. The maximum am-
plitude of this offset, which adds to the D/A converter nonlin-
earity, is 0.67 V
voltage. To maintain monotonic operation it is recommended
that V
ture range of operation. Suitable op amps are AD517L and
AD544L. The AD517L is best suited for fixed reference appli-
cations with low bandwidth requirements: it has extremely low
offset (50 V) and in most applications will not require an offset
trim. The AD544L has a much wider bandwidth and higher
slew rate and is recommended for multiplying and other appli-
cations requiring fast settling. An offset trim on the AD544L
may be necessary in some circuits.
Digital Glitches: One cause of digital glitches is capacitive
coupling from the digital lines to the OUT1 and OUT2 termi-
nals. This should be minimized by screening the analog pins of
the AD7541A (Pins 1, 2, 17, 18) from the digital pins by a
ground track run between Pins 2 and 3 and between Pins 16
and 17 of the AD7541A. Note how the analog pins are at one
end of the package and separated from the digital pins by V
and GND to aid screening at the board level. On-chip capacitive
coupling can also give rise to crosstalk from the digital-to-analog
sections of the AD7541A, particularly in circuits with high cur-
rents and fast rise and fall times.
Temperature Coefficients: The gain temperature coefficient
of the AD7541A has a maximum value of 5 ppm/ C and a typi-
cal value of 2 ppm/ C. This corresponds to worst case gain shifts
of 2 LSBs and 0.8 LSBs, respectively, over a 100 C temperature
range. When trim resistors R1 and R2 are used to adjust full-
scale range, the temperature coefficient of R1 and R2 should
also be taken into account. The reader is referred to Analog
Devices Application Note “Gain Error and Gain Temperature
Coefficient of CMOS Multiplying DACs,” Publication Number
E630c-5-3/86.
OS
be no greater than (25 10
OS
where V
OS
is the amplifier input offset
–6
) (V
REF
) over the tempera-
DD
–6–
SINGLE SUPPLY OPERATION
Figure 7 shows the AD7541A connected in a voltage switching
mode. OUT1 is connected to the reference voltage and OUT2
is connected to GND. The D/A converter output voltage is
available at the V
impedance equal to R
in this circuit.
Figure 7. Single Supply Operation Using Voltage Switch-
ing Mode
The reference voltage must always be positive. If OUT1 goes
more than 0.3 V less than GND, an internal diode will be turned
on and a heavy current may flow causing device damage (the
AD7541A is, however, protected from the SCR latch-up
phenomenon prevalent in many CMOS devices). Suitable refer-
ences include the AD580 and AD584.
The loading on the reference voltage source is code-dependent
and the response time of the circuit is often determined by the
behavior of the reference voltage with changing load conditions.
To maintain linearity, the voltage at OUT1 should remain within
2.5 V of GND, for a V
or the reference voltage at OUT1 increased to more than 2.5 V,
the differential nonlinearity of the DAC will increase and the
linearity of the DAC will be degraded.
SUPPLEMENTAL APPLICATION MATERIAL
For further information on CMOS multiplying D/A converters,
the reader is referred to the following texts:
CMOS DAC Application Guide, Publication Number
G872b-8-1/89 available from Analog Devices.
Gain Error and Gain Temperature Coefficient of CMOS
Multiplying DACs Application Note, Publication Number
E630c-5-3/86 available from Analog Devices.
Analog-Digital Conversion Handbook—available from Analog
Devices.
+2.5V
V
REF
V
i.e., D IS A FRACTIONAL REPRESENTATION OF THE DIGITAL INPUT
OUT
V
1
2
REF
OUT1
OUT2
D (1 +R2/R1) WHERE 0
GND
3
USED
REF
NOT
R
18
AD7541A
FB
pin (Pin 17) and has a constant output
BIT 1 – BIT 12
LDR
4
PINS 4–15
DD
V
. The feedback resistor R
16
of 15 V. If V
DD
V
REF
15
10k
17
D
R1
1
CA3140B
30k
R2
DD
is reduced from 15 V
V+
V–
FB
V
OUT
V
is not used
DD
= 0V TO +10V
SYSTEM
GROUND
= +15V
REV. B