AD5415YRU Analog Devices Inc, AD5415YRU Datasheet - Page 8

• Manufacturer Part Number: AD5415YRU
• Description: IC DAC DUAL 12BIT MULT 24-TSSOP
• Manufacturer: Analog Devices Inc

Specifications of AD5415YRU

• Settling Time: 120ns
• Number Of Bits: 12
• Data Interface: Serial
• Number Of Converters: 2
• Voltage Supply Source: Single Supply
• Power Dissipation (max): 3.5µW
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 24-TSSOP
• For Use With: EVAL-AD5415EBZ - BOARD EVALUATION FOR AD5415
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

AD5415
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Table 4. Pin Function Descriptions
Pin No.
1
2
3
4 to 7
8
9
10
11
12
13
14
15
16
17
18 to 21
22
23
24
Mnemonic
I
I
R
R1A, R2A,
R2_3A, R3A
V
GND
LDAC
SCLK
SDIN
SDO
SYNC
CLR
V
V
R3B, R2_3B,
R2B, R1B
R
I
I
OUT
OUT
OUT
OUT
FB
FB
REF
DD
REF
A
B
1A
2A
2B
1B
A
B
Ground Pin.
default, on power-up data is clocked into the shift register on the falling edge of SCLK. The control bits allow the
user to change the active edge to the rising edge.
alternate edge to loading data to the shift register. Writing the readback control word to the shift register makes
the DAC register contents available for readback on the SDO pin; they are clocked out on the next 16 opposite
clock edges to the active clock edge.
Description
DAC A Current Output.
DAC A Analog Ground. This pin should normally be tied to the analog ground of the system, but can be biased to
achieve single-supply operation.
DAC Feedback Resistor Pin. This pin establishes voltage output for the DAC by connecting to an external amplifier
output.
DAC A 4-Quadrant Resistors. These pins allow a number of configuration modes, including bipolar operation, with
minimum external components.
DAC A Reference Voltage Input Pin.
Load DAC Input. This pin allows asynchronous or synchronous updates to the DAC output. The DAC is
asynchronously updated when this signal goes low. Alternatively, if this line is held permanently low, an
automatic or synchronous update mode is selected, whereby the DAC is updated on the 16th clock falling edge
when the device is in standalone mode, or on the rising edge of SYNC when in daisy-chain mode.
Serial Clock Input. By default, data is clocked into the input shift register on the falling edge of the serial clock
input. Alternatively, by means of the serial control bits, the device can be configured such that data is clocked into
the shift register on the rising edge of SCLK.
Serial Data Input. Data is clocked into the 16-bit input register on the active edge of the serial clock input. By
Serial Data Output. This pin allows a number of parts to be daisy-chained. By default, data is clocked into the shift
register on the falling edge and clocked out via SDO on the rising edge of SCLK. Data is always clocked out on the
Active Low Control Input. This pin provides the frame synchronization signal for the input data. When SYNC goes
low, it powers on the SCLK and SDIN buffers, and the input shift register is enabled. Data is loaded into the shift
register on the active edge of the subsequent clocks. In standalone mode, the serial interface counts the clocks,
and data is latched into the shift register on the 16th active clock edge.
Active Low Control Input. This pin clears the DAC output, input, and DAC registers. Configuration mode allows the user
to enable the hardware CLR pin as a clear to zero scale or midscale as required.
Positive Power Supply Input. This part can be operated from a supply of 2.5 V to 5.5 V.
DAC B Reference Voltage Input Pin.
DAC B 4-Quadrant Resistors. These pins allow a number of configuration modes, including bipolar operation, with
a minimum of external components.
DAC B Feedback Resistor Pin. This pin establishes voltage output for the DAC by connecting to the external
amplifier output.
DAC B Analog Ground. This pin should normally be tied to the analog ground of the system, but can be biased to
achieve single-supply operation.
DAC B Current Output.
I
I
R2_3A
V
OUT
OUT
LDAC
SCLK
R
REF
SDIN
GND
R3A
R1A
R2A
FB
1A
2A
A
A
Figure 6. Pin Configuration
12
10
11
1
2
3
4
5
6
7
8
9
Rev. B | Page 8 of 32
(Not to Scale)
AD5415
TOP VIEW
24
23
22
21
20
19
18
17
16
15
14
13
I
I
R
R1B
R2B
R2_3B
R3B
V
V
CLR
SYNC
SDO
OUT
OUT
REF
DD
FB
B
1B
2B
B