MAX5852ETL+ Maxim Integrated Products, MAX5852ETL+ Datasheet - Page 18
![IC DAC 8BIT DUAL 165MSPS 40-TQFN](/photos/6/65/66502/40-qfn_pkg_sml.jpg)
MAX5852ETL+
Manufacturer Part Number
MAX5852ETL+
Description
IC DAC 8BIT DUAL 165MSPS 40-TQFN
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX5852ETL.pdf
(18 pages)
Specifications of MAX5852ETL+
Settling Time
12ns
Number Of Bits
8
Data Interface
Parallel
Number Of Converters
2
Voltage Supply Source
Single Supply
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
40-TQFN Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power Dissipation (max)
-
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
18
© 2004 Maxim Integrated Products
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
go to www.maxim-ic.com/packages.)
go to www.maxim-ic.com/packages.)
go to www.maxim-ic.com/packages.)
Dual, 8-Bit, 165Msps, Current-Output DAC
____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
NOTES:
10. WARPAGE SHALL NOT EXCEED 0.10 mm.
1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994.
2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES.
3. N IS THE TOTAL NUMBER OF TERMINALS.
4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO JESD 95-1
5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.25 mm AND 0.30 mm
6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY.
7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION.
8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS.
9. DRAWING CONFORMS TO JEDEC MO220, EXCEPT FOR 0.4mm LEAD PITCH PACKAGE T4866-1.
SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE
ZONE INDICATED. THE TERMINAL #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE.
FROM TERMINAL TIP.
D
Printed USA
D/2
e
A1
A2
E/2
A
E
L1
(NE-1) X e
L
L
is a registered trademark of Maxim Integrated Products.
k
C L
(ND-1) X e
e
D2
C L
PACKAGE OUTLINE
36, 40, 48L THIN QFN, 6x6x0.8mm
PACKAGE OUTLINE
36, 40, 48L THIN QFN, 6x6x0.8mm
D2/2
e
21-0141
21-0141
b
Package Information
Package Information
Package Information
Package Information
L
E2/2
C L
k
C L
e
E2
E
E
L
1
2
2
2