ADDAC80NZ-CBI-V Analog Devices Inc, ADDAC80NZ-CBI-V Datasheet - Page 13

• Manufacturer Part Number: ADDAC80NZ-CBI-V
• Description: IC DAC 12-BIT BINARY MONO 24-DIP
• Manufacturer: Analog Devices Inc

Specifications of ADDAC80NZ-CBI-V

• Data Interface: Parallel
• Settling Time: 2µs
• Number Of Bits: 12
• Number Of Converters: 1
• Voltage Supply Source: Dual ±
• Power Dissipation (max): 300mW
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Package / Case: 24-DIP (0.600", 15.24mm)
• Resolution (bits): 12bit
• Input Channel Type: Parallel
• Supply Current: 20mA
• Digital Ic Case Style: DIP
• No. Of Pins: 24
• Operating Temperature Range: 0°C To +70°C
• Msl: MSL 3 - 168 Hours
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Output
Range
± 10 V
± 5 V
± 2.5 V
0 V to 10 V
0 V to 5 V
NOTES
1. INDEX AREA; A NOTCH OR A LEAD ONE IDENTIFICATION MARK IS LOCATED ADJACENT TO LEAD ONE.
2. THE MINIMUM LIMIT FOR DIMENSION MAY BE 0.023" (0.58 mm) FOR ALL FOUR CORNER LEADS ONLY.
3. DIMENSION SHALL BE MEASURED FROM THE SEATING PLANE TO THE BASE PLANE.
4. THIS DIMENSION ALLOWS FOR OFF-CENTER LID, MENISCUS AND GLASS OVERRUN.
5. APPLIES TO ALL FOUR CORNERS.
6. ALL LEADS — INCREASE MAXIMUM LIMIT BY 0.003" (0.08 mm) MEASURED AT THE CENTER OF THE FLAT,
7. TWENTY TWO SPACES.
8. CONTROLLING DIMENSIONS ARE IN MILLIMETERS. INCH DIMENSIONS ARE ROUNDED-OFF MILLIMETER
WHEN HOT SOLDER DIP LEAD FINISH IS APPLIED.
EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
0.225 (5.72)
SEE NOTE 1
0.200 (5.08)
0.120 (3.05)
PIN 1
0.005 (0.13) MIN
MAX
CONTROLLING DIMENSIONS ARE IN MILLIMETERS: INCH DIMENSIONS
ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE
ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
0.200 (5.05)
0.125 (3.18)
0.023 (0.58)
0.014 (0.36)
(6.35)
0.250
MAX
Table V. External Op Amp Voltage Mode Connections
PIN 1
24
Digital
Input Codes
COB or CTC
COB or CTC
COB or CTC
CSB
CSB
1
0.022 (0.558)
0.014 (0.356)
1.290 (32.77) MAX
24
0.110 (2.79)
0.090 (2.29)
SEE NOTE 7
1
SEE NOTE 4
SEE NOTE 5
Dimensions shown in inches and (mm).
24-Lead Ceramic DIP (D-24)
24-Lead Plastic DIP (N-24A)
1.290 (32.70)
1.150 (29.30)
OUTLINE DIMENSIONS
(2.54)
0.100
BSC
SEE NOTE 2, 6
0.098 (2.49) MAX
0.070 (1.78)
0.030 (0.76)
Connect
A to
19
18
18
18
18
13
12
0.070 (1.77)
0.030 (0.77)
0.610 (15.49)
0.500 (12.70)
0.075 (1.91)
0.015 (0.38)
SEE NOTE 3
SEE NOTE 4
SEATING
PLANE
0.060 (1.52)
0.015 (0.38)
12
13
0.150
(3.81)
MIN
0.580 (14.73)
0.485 (12.32)
SEATING
PLANE
Connect
Pin 17 to
15
15
15
21
21
0.150
(3.81)
MIN
0.620 (15.75)
0.590 (14.99)
0.625 (15.87)
0.600 (15.24)
0.015 (0.38)
0.008 (0.20)
SEE NOTE 6
ADDAC80/ADDAC85/ADDAC87
Connect
Pin 19 to
A
NC
15
NC
15
0.015 (0.381)
0.008 (0.204)
0.195 (4.95)
0.125 (3.18)
Connect
Pin 16 to
24
24
24
24
24