1408312-1 TE Connectivity, 1408312-1 Datasheet - Page 3

• Manufacturer Part Number: 1408312-1
• Description: RF/COAXIAL, MMCX PLUG, 50OHM, CRIMP/SLDR
• Manufacturer: TE Connectivity

Specifications of 1408312-1

• Connector Type: MMCX Coaxial
• Body Style: Straight Plug
• Coaxial Termination: Solder / Crimp
• Impedance: 50ohm
• Rg Cable Type: RG-316
• Connector Mounting: Cable
• Rohs Compliant: Yes
• Connector Impedance (?): 50
• Cable Diameter (max.) (mm [in]): 2.25 [0.089]
• Assembly Instruction: MV4
• Connector Style: Plug
• Coaxial Cable Type: RG 316
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant
• Applies To: Coaxial Cable
• Packaging Quantity: 100

Rev B
Mechanical endurance.
Engaging and separating forces.
Contact captivation.
Cable clam ping device, axial.
Cable clam ping device, torsion.
Bending m om ent.
Rapid change of tem perature.
High tem perature.
Dam p heat, steady state.
Salt m ist.
Test Description
See Note.
18 N [4.05 lbf] m axim um engaging
force.
6 N [1.34 lbf] m inim um separating
force.
10 N [2.25 lbf] m inim um .
32 N [7.2 lbf] m inim um .
0.05 N•m [.04 lbf-ft] m inim um .
0.05 N•m [.04 lbf-ft] m inim um .
See Note.
See Note.
See Note.
See Note.
Figure 1 (continued)
ENVIRONMENTAL
Requirem ent
CECC 22 220, 4.5.5.
CECC 22 220, 4.5.5.
CECC 22 220, 4.7.1.
Manually m ate and unm ate
specim ens for 500 cycles at a
m axim um rate of 15 cycles per
m inute.
CECC 22 220, 4.5.4.
Measure force necessary to
engage (m ate) and separate
(unm ate) specim ens at a m axim um
rate of 12.7 m m [.5 in] per m inute.
CECC 22 220, 4.5.2.
Apply axial force to center contact
pin at a m axim um rate of 12.7 m m
[.5 in] per m inute.
Apply tensile force to cable at a
m axim um rate of 12.7 m m [.5 in]
per m inute.
Apply axial torque to cable.
CECC 22 220, 4.5.9.
CECC 22 220, 4.6.7.
Subject m ated specim ens to 5
cycles between -55 and 155°C with
30 m inute dwells at tem perature
extrem es and 2 to 3 m inute
transition between tem perature
extrem es.
CECC 22 220, 4.7.2.
Subject m ated specim ens to 155°C
for 1000 hours.
CECC 22 220, 4.6.6.
Subject m ated specim ens to 40°C
and 93% RH for 96 hours. Voltage
proof shall be perform ed within 15
m inutes after specim ens are
rem oved from the cham ber.
CECC 22 220, 4.6.10.
Subject m ated specim ens to salt
spray for 48 hours.
Procedure
108-2084
3 of 6