AD5312BRMZ Analog Devices Inc, AD5312BRMZ Datasheet - Page 20
![IC DAC 10BIT DUAL R-R 10-MSOP](/photos/6/60/66034/505-10-msop_sml.jpg)
AD5312BRMZ
Manufacturer Part Number
AD5312BRMZ
Description
IC DAC 10BIT DUAL R-R 10-MSOP
Manufacturer
Analog Devices Inc
Datasheet
1.AD5302ARMZ.pdf
(24 pages)
Specifications of AD5312BRMZ
Data Interface
Serial
Settling Time
6µs
Number Of Bits
10
Number Of Converters
2
Voltage Supply Source
Single Supply
Power Dissipation (max)
2.5mW
Operating Temperature
-40°C ~ 105°C
Mounting Type
Surface Mount
Package / Case
10-MSOP, Micro10™, 10-uMAX, 10-uSOP
Resolution (bits)
10bit
Sampling Rate
143kSPS
Input Channel Type
Serial
Supply Voltage Range - Analog
2.5V To 5.5V
Supply Current
300µA
Digital Ic Case Style
SOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD5312BRMZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
AD5302/AD5312/AD5322
COARSE AND FINE ADJUSTMENT USING THE
AD5302/AD5312/AD5322
The DACs in the AD5302/AD5312/AD5322 can be paired
together to form a coarse and fine adjustment function, as
shown in Figure 44. DAC A is used to provide the coarse
adjustment while DAC B provides the fine adjustment. Varying
the ratio of R1 and R2 changes the relative effect of the coarse
and fine adjustments. With the resistor values and external
reference shown, the output amplifier has unity gain for the
DAC A output, so the output range is 0 V to 2.5 V − 1 LSB. For
DAC B, the amplifier has a gain of 7.6 × 10
range equal to 19 mV.
The circuit is shown with a 2.5 V reference, but reference
voltages up to V
rail-to-rail output swing.
EXT
REF
GND
V
IN
V
OUT
0.1µF
1µF
DD
Figure 44. Coarse/Fine Adjustment
can be used. The op amps indicated allow a
10µF
V
AD5302/AD5312/
V
REF
REF
A
B
AD5322
V
DD
GND
V
DD
= 5V
V
V
OUT
OUT
51.2kΩ
B
A
R3
51.2kΩ
51.2kΩ
390Ω
R1
R2
R2
–3
, giving DAC B a
900Ω
+5V
R4
AD820/
OP295
V
OUT
Rev. C | Page 20 of 24
POWER SUPPLY BYPASSING AND GROUNDING
In any circuit where accuracy is important, careful considera-
tion of the power supply and ground return layout helps to
ensure the rated performance. The printed circuit board on
which the AD5302/AD5312/AD5322 is mounted should be
designed so that the analog and digital sections are separated
and confined to certain areas of the board. If the AD5302/
AD5312/AD5322 are in a system where multiple devices require
an AGND-to-DGND connection, the connection should be
made at one point only. The star ground point should be
established as close as possible to the AD5302/AD5312/
AD5322. The part should have ample supply bypassing of 10 μF
in parallel with 0.1 μF on the supply located as close as possible
to the package, ideally right up against the device. The 10 μF
capacitors are the tantalum bead type. The 0.1 μF capacitor
should have low effective series resistance (ESR) and effective
series inductance (ESI), similar to the common ceramic types
that provide a low impedance path to ground at high frequencies
that handle transient currents due to internal logic switching.
The power supply lines of the AD5302/AD5312/AD5322
should use as large a trace as possible to provide low impedance
paths and reduce the effects of glitches on the power supply line.
Fast switching signals such as clocks should be shielded with
digital ground to avoid radiating noise to other parts of the board,
and should never be run near the reference inputs. Avoid crossover
of digital and analog signals. Traces on opposite sides of the
board should run at right angles to each other. This reduces the
effects of feedthrough through the board. A microstrip technique
is by far the best, but is not always possible with a double-sided
board. In this technique, the component side of the board is dedi-
cated to ground while signal traces are placed on the solder side.