MCP4641-103E/ST Microchip Technology, MCP4641-103E/ST Datasheet - Page 48
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
MCP4641-103E/ST
Manufacturer Part Number
MCP4641-103E/ST
Description
IC DGTL POT 10K 256TAPS 14-TSSOP
Manufacturer
Microchip Technology
Specifications of MCP4641-103E/ST
Taps
129
Resistance (ohms)
10K
Number Of Circuits
2
Temperature Coefficient
150 ppm/°C Typical
Memory Type
Non-Volatile
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
14-TSSOP
Resistance In Ohms
10K
End To End Resistance
100kohm
Track Taper
Linear
Resistance Tolerance
± 20%
No. Of Steps
128
Supply Voltage Range
2.7V To 5.5V
Control Interface
I2C, Serial
No. Of Pots
Dual
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
MCP453X/455X/463X/465X
6.2.4
The address byte is the first byte received following the
START condition from the master device. The address
contains four (or more) fixed bits and (up to) three user
defined hardware address bits (pins A2, A1, and A0).
These 7-bits address the desired I
A7:A4 address bits are fixed to “0101” and the device
appends the value of following three address pins (A2,
A1, A0). Address pins that are not present on the
device are pulled up (a bit value of ‘1’).
Since there are up to three adress bits controlled by
hardware pins, there may be up to eight MCP4XXX
devices on the same I
Figure 6-9
contains the seven address bits. There is also a read/
write bit.
Hardware Address Pins
The hardware address bits (A2, A1, and A0)
correspond to the logic level on the associated address
pins. This allows up to eight devices on the bus.
These pins have a weak pull-up enabled when the V
< V
technology and exhibits the same characteristics as the
High-voltage tolerant I/O structure.
The state of the A0 address pin is latch on POR/BOR.
This is required since High Voltage commands force
this pin (HVC/A0) to the V
DS22096A-page 48
BOR
. The weak pull-up utilizes the “smart” pull-up
Table 6-2
shows the slave address byte format, which
ADDRESSING
shows the fixed address for device.
2
C bus.
IHH
level.
2
C device. The
DD
FIGURE 6-9:
I
TABLE 6-2:
6.2.5
The MCP45XX/46XX implements slope control on the
SDA output.
As the device transitions from HS mode to FS mode,
the slope control parmameter will change from the HS
specification to the FS specification.
For Fast (FS) and High-Speed (HS) modes, the device
has a spike suppression and a Schmidt trigger at SDA
and SCL inputs.
2
Start
bit
Device
MCP45X1 ‘0101 11’b + A0
MCP45X2 ‘0101 1’b + A1:A0
MCP46X1 ‘0101’b + A2:A1:A0 Supports up to 8
MCP46X2 ‘0101 1’b + A1:A0
Note 1:
A = 0 = Slave Device Acknowledges byte
A = 1 = Slave Device does not Acknowledge byte
A bit (controlled by slave device)
S A6 A5 A4 A3 A2 A1 A0 R/W A/A
C Control Byte.
“0” “1” “0” “1”
A0 is used for High-Voltage commands
and the value is latched at POR.
SLOPE CONTROL
Address
Slave Address
DEVICE SLAVE ADDRESSES
Slave Address Bits in the
See
© 2008 Microchip Technology Inc.
R/W = 0 = write
R/W = 1 = read
R/W bit
Table 6-2
Comment
Supports up to 2
devices. Note 1
Supports up to 4
devices. Note 1
devices. Note 1
Supports up to 4
devices. Note 1