MCP4641-103E/ST Microchip Technology, MCP4641-103E/ST Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
MCP4641-103E/ST
Manufacturer Part Number
MCP4641-103E/ST
Description
IC DGTL POT 10K 256TAPS 14-TSSOP
Manufacturer
Microchip Technology
Specifications of MCP4641-103E/ST
Taps
129
Resistance (ohms)
10K
Number Of Circuits
2
Temperature Coefficient
150 ppm/°C Typical
Memory Type
Non-Volatile
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
14-TSSOP
Resistance In Ohms
10K
End To End Resistance
100kohm
Track Taper
Linear
Resistance Tolerance
± 20%
No. Of Steps
128
Supply Voltage Range
2.7V To 5.5V
Control Interface
I2C, Serial
No. Of Pots
Dual
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
MCP453X/455X/463X/465X
FIGURE 1-2:
TABLE 1-2:
DS22096A-page 14
I
Note 1:
2
Param.
C AC Characteristics
No.
100
101
2:
3:
4:
5:
6:
7:
SDA
Out
SDA
In
SCL
As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region
(minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions.
A fast-mode (400 kHz) I
requirement t
stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal,
it must output the next data bit to the SDA line
T
the SCL line is released.
The MCP46X1/MCP46X2 device must provide a data hold time to bridge the undefined part between V
and V
must be tested in order to ensure that the output data will meet the setup and hold specifications for the
receiving device.
Use Cb in pF for the calculations.
Not Tested
A Master Transmitter must provide a delay to ensure that difference between SDA and SCL fall times do
not unintentionally create a Start or Stop condition.
Ensured by the T
R
T
T
Sym
max.+t
HIGH
LOW
IL
I
2
of the falling edge of the SCL signal. This specification is not a part of the I
C BUS DATA REQUIREMENTS (SLAVE MODE)
SU;DAT
I
90
Characteristic
2
Clock high time
Clock low time
C Bus Data Timing.
SU;DAT
103
91
AA
= 1000 + 250 = 1250 ns (according to the standard-mode I
3.4 MHz specification test.
≥ 250 ns must then be met. This will automatically be the case if the device does not
109
2
C-bus device can be used in a standard-mode (100 kHz) I
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
Operating Voltage V
100 kHz mode
400 kHz mode
1.7 MHz mode
3.4 MHz mode
100 kHz mode
400 kHz mode
1.7 MHz mode
3.4 MHz mode
100
106
109
101
DD
4000
4700
1300
range is described in
Min
600
120
320
160
60
107
–40°C ≤ T
Max
—
—
—
—
—
—
A
≤ +125°C (Extended)
Units
ns
ns
ns
ns
ns
ns
ns
ns
AC/DC characteristics
© 2008 Microchip Technology Inc.
2
C bus specification) before
92
1.8V-5.5V
2.7V-5.5V
4.5V-5.5V
1.8V-5.5V
2.7V-5.5V
4.5V-5.5V
4.5V-5.5V
4.5V-5.5V
102
2
2
C specification, but
C-bus system, but the
110
Conditions
IH