35TLV470M12.5X13.5 RUBYCON, 35TLV470M12.5X13.5 Datasheet - Page 3

• Manufacturer Part Number: 35TLV470M12.5X13.5
• Description: CAPACITOR, SMD, 35V, 470UF
• Manufacturer: RUBYCON
• Series: TLVr

Specifications of 35TLV470M12.5X13.5

• Capacitor Dielectric Type: Aluminium Electrolytic
• Capacitance: 470µF
• Capacitance Tolerance: ± 20%
• Voltage Rating: 35V
• Life Time @ Temperature: 5000 Hours @ 105°C
• Height: 13.5mm
• Diameter: 12.5mm
• Rohs Compliant: Yes
• Capacitor Mounting: SMD
• Lead Spacing: 4.5mm

5.Load life Test
6.Shelf life Test
7. Reflow soldering condition.
8.Correction factor for ripple current
current) at 105±2°C for 5000
following requirements.
specified in JIS C 5141 paragraph 5.2, then capacitor shall meet following requirement.
(1) Temperature at surface of capacitor shall not exceed T°C.
(2) Period that temperature at surface of capacitor becomes more
(3) Holding time in the peak temperature shall be as short as
possible.
(4) Preheat shall be made at 100°C to 180°C and for maximum 150
(5) Reflow soldering process shall be 1 cycle.
Capacitor under test shall be applied the rated voltage continuously through 1000 ohm series protective resistor (with maximum ripple
Capacitor under test shall be stored at 105±2°C without loading. After 1000
◊Temperature coefficient shows a limit of ripple current exceeding the rated ripple current that can be passed through a capacitor at each
◊ Ripple voltage with wide amplitude
7-1 Capacitors shall be proof the following reflow soldering condition.
than 200°C and 230°C shall not exceed t and t1 seconds,
respectively.
seconds.
φ12.5x13.5
7-2 Notes.
The maximum permissible ripple current is the maximum A.C. current at 120Hz and can be applied at maximum operating temperature.
The combined value of D.C. voltage and the peak A.C. voltage shall not exceed the rated voltage and shall not be reverse voltage.
< Frequency Coefficient >
< Temperature Coefficient >
temperature when the life expectancy of a capacitor becomes to be nearly equal with the lifetime at the rated maximum operating
temperature.
Use of aluminum electrolytic capacitor under ripple voltage with wide amplitude is equivalent to quick charge-discharge operation.
When ripple voltage with the amplitude over 70Vp-p is expected for the products with rated voltage over 100V, please contact us.
(Temperature measurement point is top of case.)
(1) Reflow soldering condition (reflow time, temperature) depends on following points.
(2) The thermocouple (Type CA φ0.1mm dia) shall be fixed to the surface of capacitor by adhesives.
Size
Capacitance Change : within
Dissipation Factor
Leakage Current
Appearance
Capacitance Change : within
Dissipation Factor
Leakage Current
Appearance
Freq. (Hz)
Multiplier
Please confirm your reflow profile.
Ambient Temperature(°C)
Coefficient
• Kind of reflow oven.
• Mounting condition (part size, PW-board size etc.) of parts on the PW-board.
TLV SERIES
T°C
240
0.60
: less than 200% of the specified value.
: less than the specified value.
: notable changes shall not be found.
: less than 200% of the specified value.
: less than the specified value.
: notable changes shall not be found.
120
+
72
0
T1°C
hours. After the test and returned in standard condition for 2 hours or more, and the capacitor shall meet
230
±
±
30% of the initially measured value.
30% of the initially measured value.
0.85
• Kind of PW-board.
105
1.0
1k
t (sec.)
60
0.95
1.7
10k
85
t1 (sec.)
RUBYCON CORPORATION
30
100k≤
1.00
2.1
65≥
 
100
200
180
+
T
T
48
1
0
<Temperature profile>
Preheat 150sec MAX
hours, capacitor shall be subjected to voltage treatment
Time (sec)
Peak temperature · 5sec.
t sec MAX
t
1
sec MAX
PAGE
T C Max
2 / 5