DS1866Z+ Maxim Integrated Products, DS1866Z+ Datasheet - Page 2

• Manufacturer Part Number: DS1866Z+
• Description: IC POT TRIM LOG 2.7-5.5V 8-SOIC
• Manufacturer: Maxim Integrated Products

Specifications of DS1866Z+

• Taps: 8
• Resistance (ohms): 10K
• Number Of Circuits: 1
• Temperature Coefficient: 750 ppm/°C Typical
• Memory Type: Volatile
• Interface: 3-Input Parallel
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Resistance In Ohms: 10K
• Number Of Pots: Single
• Taps Per Pot: 8
• Resistance: 10 KOhms
• Wiper Memory: Volatile
• Digital Interface: Parallel (3-Input)
• Operating Supply Voltage: 2.7 V to 5.5 V
• Supply Current: 50 uA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Description/function: Log Trimmer Potentiometer
• Mounting Style: Through Hole
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Tolerance: 20 %
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

OPERATION
The DS1866 is a single volatile potentiometer. The device has a total of eight positions providing a
resolution of 5 dB per step and giving a total attenuation range of 0 dB to -35 dB. These tap points are
accessible to the W-terminal whose position is controlled via a 3-terminal parallel port consisting of input
signals P0, P1, and P2. A block diagram of the DS1866 is shown in Figure 1.
Wiper position setting of the DS1866 is determined by the states of the P0, P1, and P2 input terminals.
Table 1 below outlines position setting versus value of the parallel port inputs. A Position-0 setting places
the wiper position at the L-terminal of the potentiometer and provides 35 dB of attenuation. As wiper
position increases, attenuation decreases with Position-7 giving 0 dB of attenuation.
On power-up, the wiper position of the DS1866 will be set to the P0, P1, and P2 values.
PIN DESCRIPTIONS
V
volts.
GND - Ground Terminal.
H - High-end Resistor. This is the high-end terminal of the potentiometer. It is not required that this
terminal be connected to a potential greater than the L-terminal. Maximum voltage on the H-terminal can
not exceed the power supply voltage, V
L - Low-end Resistor. This is the low-end terminal of the potentiometer. It is not required that this
terminal be connected to a potential less than the H-terminal. Maximum voltage on the L-terminal can not
exceed the power-supply voltage, V
W - Wiper of the Potentiometer. This pin is the wiper terminal of the potentiometer. Its position on the
resistor array is controlled by the 3-terminal parallel port. Maximum voltage on the W-terminal can not
exceed the power supply voltage, V
P0 - Bit 0. P0 is the bit 0 data input to the parallel port.
P1 - Bit 1. P1 is the bit 1 data input to the parallel port.
P2 - Bit 2. P2 is the bit 2 data input to the parallel port.
P2 P1 P0
CC
(binary)
000
001
010
011
100
101
110
111
- Power Supply Terminal. The DS1866 will support supply voltages ranging from +2.7 to +5.5
Position
Wiper
0
1
2
3
4
5
6
7
Attenuation
35 dB
30 dB
25 dB
20 dB
15 dB
10 dB
(dB)
5 dB
0 dB
CC
CC
, or go below ground.
, or go below ground.
CC
, or go below ground.
2 of 5
102199
DS1866