AD9276BSVZ Analog Devices Inc, AD9276BSVZ Datasheet
AD9276BSVZ
Specifications of AD9276BSVZ
Available stocks
Related parts for AD9276BSVZ
AD9276BSVZ Summary of contents
Page 1
FEATURES 8 channels of LNA, VGA, AAF, ADC, and I/Q demodulator Low noise preamplifier (LNA) Input-referred noise: 0.75 nV/√Hz typical at 5 MHz (gain = 21.3 dB) SPI-programmable gain: 15.6 dB/17.9 dB/21.3 dB Single-ended input: V maximum = 733 mV ...
Page 2
AD9276 TABLE OF CONTENTS Features .............................................................................................. 1 Applications ....................................................................................... 1 Product Highlights ........................................................................... 1 Functional Block Diagram .............................................................. 1 Revision History ............................................................................... 2 General Description ......................................................................... 3 Specifications ..................................................................................... 4 AC Specifications .......................................................................... 4 Digital Specifications ................................................................... 7 Switching Specifications ...
Page 3
GENERAL DESCRIPTION The AD9276 is designed for low cost, low power, small size, and ease of use. It contains eight channels of a variable gain amplifier (VGA) with a low noise preamplifier (LNA); an anti- aliasing filter (AAF); a 12-bit, ...
Page 4
AD9276 SPECIFICATIONS AC SPECIFICATIONS AVDD1 = 1.8 V, AVDD2 = 3.0 V, DRVDD = 1.8 V, 1.0 V internal ADC reference, f PGA gain = 27 dB, GAIN− = 0.8 V, AAF LPF cutoff = f Mode ...
Page 5
Parameter Noise Figure Active Termination Matched Mode I/Mode II/Mode III Unterminated Correlated Noise Ratio Output Offset Signal-to-Noise Ratio (SNR) Mode I/Mode II/Mode III Harmonic Distortion Mode I/Mode II/Mode III Second Harmonic Third Harmonic Two-Tone Intermodulation (IMD3) Channel-to-Channel Crosstalk Channel-to-Channel ...
Page 6
AD9276 1 Parameter Input-Referred Noise Voltage Noise Figure Input-Referred Dynamic Range Output-Referred SNR Two-Tone Intermodulation (IMD3) Quadrature Phase Error I/Q Amplitude Imbalance Channel-to-Channel Matching POWER SUPPLY Mode I/Mode II/Mode III AVDD1 AVDD2 DRVDD I AVDD1 I AVDD2 I DRVDD Total ...
Page 7
DIGITAL SPECIFICATIONS AVDD1 = 1.8 V, AVDD2 = 3.0 V, DRVDD = 1.8 V, 1.0 V internal ADC reference, f Table 2. Parameter 1 CLOCK INPUTS (CLK+, CLK−) Logic Compliance 2 Differential Input Voltage Input Common-Mode Voltage Input Resistance (Differential) ...
Page 8
AD9276 SWITCHING SPECIFICATIONS AVDD1 = 1.8 V, AVDD2 = 3.0 V, DRVDD = 1.8 V, 1.0 V internal ADC reference, f Table 3. 1 Parameter 2 CLOCK Clock Rate 40 MSPS (Mode I) 65 MSPS (Mode II) 80 MSPS (Mode ...
Page 9
ADC TIMING DIAGRAMS N – 1 AIN t EH CLK– CLK+ t CPD DCO– DCO+ t FCO FCO– FCO DOUTx– DOUTx+ N – 1 AIN t EH CLK– CLK+ t CPD DCO– DCO+ t FCO FCO– FCO+ t ...
Page 10
AD9276 ABSOLUTE MAXIMUM RATINGS Table 4. Parameter AVDD1 to GND AVDD2 to GND DRVDD to GND GND to GND AVDD2 to AVDD1 AVDD1 to DRVDD AVDD2 to DRVDD Digital Outputs (DOUTx+, DOUTx−, DCO+, DCO−, FCO+, FCO−) to GND CLK+, CLK−, ...
Page 11
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS PIN 1 LI-E 1 INDICATOR LG-E 2 AVDD2 3 AVDD1 4 LO-F 5 LOSW-F 6 LI-F 7 LG-F 8 AVDD2 9 AVDD1 10 LO-G 11 LOSW-G 12 LI-G 13 LG-G 14 AVDD2 15 AVDD1 16 ...
Page 12
AD9276 Pin No. Name 23 CLK− 24 CLK+ 26, 47 DRVDD 27 DOUTH− 28 DOUTH+ 29 DOUTG− 30 DOUTG+ 31 DOUTF− 32 DOUTF+ 33 DOUTE− 34 DOUTE+ 35 DCO− 36 DCO+ 37 FCO− 38 FCO+ 39 DOUTD− 40 DOUTD+ 41 ...
Page 13
Pin No. Name 89 RBIAS 90 VREF 92 CWI− 93 CWI+ 94 CWQ− 95 CWQ+ 99 LO-E 100 LOSW-E Description External Resistor to Set the Internal ADC Core Bias Current. Voltage Reference Input/Output. CW Doppler I Output Complement. CW Doppler ...
Page 14
AD9276 TYPICAL PERFORMANCE CHARACTERISTICS TGC MODE MSPS MHz Ω, LNA gain = 21.3 dB, LNA bias = high, PGA gain = 27 dB, AAF LPF cutoff = f SAMPLE IN S ...
Page 15
CODES Figure 11. Output-Referred Noise Histogram, GAIN+ = 0.0 V 180k 160k 140k 120k 100k 80k 60k 40k ...
Page 16
AD9276 0 –10 –20 –30 –40 GAIN+ = 0.4V –50 –60 GAIN+ = 1.6V –70 GAIN+ = 1.0V –80 – INPUT FREQUENCY (MHz) Figure 17. Second-Order Harmonic Distortion vs. Frequency, AIN = −1.0 dBFS 0 ...
Page 17
CW DOPPLER MODE f = 2.5 MHz at −3 dBFS MHz 4LO 1.2 1.0 0.8 0.6 0.4 0.2 0 –0.2 –0.4 –0.6 –0.8 –1.0 –1.2 100 1k BASEBAND FREQUENCY (Hz) Figure 23. Quadrature Phase Error ...
Page 18
AD9276 170 168 166 LNA GAIN = 15.6dB 164 LNA GAIN = 17.9dB 162 LNA GAIN = 21.3dB 160 158 156 154 FREQUENCY (MHz) Figure 29. Small-Signal Dynamic Range vs. RF Frequency ...
Page 19
EQUIVALENT CIRCUITS V AVDD2 CM 15kΩ LI-x, LG-x Figure 30. Equivalent LNA Input Circuit AVDD2 AVDD2 10Ω LO-x, LOSW-x Figure 31. Equivalent LNA Output Circuit AVDD1 350Ω CLK+ 10kΩ AVDD1 10kΩ 350Ω CLK– Figure 32. Equivalent Clock Input Circuit AVDD2 ...
Page 20
AD9276 AVDD1 AVDD1 70kΩ 350Ω CSB Figure 38. Equivalent CSB Input Circuit VREF 6kΩ Figure 39. Equivalent VREF Circuit 100Ω RBIAS Figure 40. Equivalent RBIAS Circuit AVDD2 GAIN+ Figure 41. Equivalent GAIN+ Input Circuit AVDD2 GAIN– Figure 42. Equivalent GAIN− ...
Page 21
THEORY OF OPERATION ULTRASOUND The primary application for the AD9276 is medical ultrasound. Figure 45 shows a simplified block diagram of an ultrasound system. A critical function of an ultrasound system is the time gain control (TGC) compensation for physiological ...
Page 22
AD9276 4LO– 4LO+ RESET R LO-x FB1 R LOSW-x FB2 T/R SWITCH C S LI-x LG TRANSDUCER CHANNEL OVERVIEW Each channel contains both a TGC signal path and a CW Doppler signal path. Common to both ...
Page 23
Low value feedback resistors and the current-driving capability of the output stage allow the LNA to achieve a low input- referred noise voltage of 0.75 nV/√Hz (at a gain of 21.3 dB). This is achieved with a current consumption of ...
Page 24
AD9276 LNA Noise The short-circuit noise voltage (input-referred noise important limit on system performance. The short-circuit noise voltage for the LNA is 0.75 nV/√ gain of 21.3 dB, including the VGA noise at a VGA postamp ...
Page 25
INPUT OVERDRIVE Excellent overload behavior is of primary importance in ultrasound. Both the LNA and VGA have built-in overdrive protection and quickly recover after an overload event. Input Overload Protection As with any amplifier, voltage clamping prior to the inputs ...
Page 26
AD9276 I/Q Demodulator and Phase Shifter The I/Q demodulators consist of double-balanced passive mixers. The RF input signals are converted into currents by transconduc- tance stages that have a maximum differential input signal capability matching the LNA output full scale. ...
Page 27
LNA CHANNEL A CHANNEL H LNA Phase Compensation and Analog Beamforming Beamforming, as applied to medical ultrasound, is defined as the phase alignment and summation of signals generated from a common source but received at different times by a multielement ...
Page 28
AD9276 For CW Doppler operation, the AD9276 integrates the LNA, phase shifter, frequency conversion, and I/Q demodulation into a single package and directly yields the baseband signal. Figure simplified diagram showing the concept for four channels. The ...
Page 29
TGC OPERATION The TGC signal path is fully differential throughout to maxi- mize signal swing and reduce even-order distortion; however, the LNAs are designed to be driven from a single-ended signal source. Gain values are referenced from the single-ended LNA ...
Page 30
AD9276 Table 10. Sensitivity and Dynamic Range Trade-Offs LNA Gain Full-Scale Input Noise (V/V) (dB) Input (V p-p) (nV/√Hz) 6 15.6 0.733 0.98 8 17.9 0.550 0.86 12 21.3 0.367 0.75 1 LNA: output full scale = 4.4 V p-p ...
Page 31
PGA GAIN = 21dB 0.4 PGA GAIN = 24dB 0.3 0.2 0.1 PGA GAIN = 27dB PGA GAIN = 30dB 0 0 0.2 0.4 0.6 0.8 1.0 GAIN+ (V) Figure 57. LNA with 17.9 dB Gain Setting/VGA Full-Scale ...
Page 32
AD9276 499Ω ±0.4V DC 100Ω AT 0.8V CM GAIN+ 0.01µF AD8138 100Ω GAIN– ±0.4V DC 0.01µF AT 0.8V CM 499Ω Figure 61. Differential GAIN+, GAIN− Pin Configuration VGA Noise In a typical application, a VGA compresses a wide dynamic range ...
Page 33
ADC The AD9276 uses a pipelined ADC architecture. The quantized output from each stage is combined into a 12-bit result in the digital correction logic. The pipelined architecture permits the first stage to operate on a new input sample and ...
Page 34
AD9276 The duty cycle stabilizer uses a delay-locked loop (DLL) to create the nonsampling edge result, any changes to the sampling frequency require approximately eight clock cycles to allow the DLL to acquire and lock to the new ...
Page 35
By asserting the PDWN pin high, the AD9276 is placed into power-down mode. In this state, the device typically dissipates 5 mW. During power-down, the LVDS output drivers are placed into a high impedance state. The AD9276 returns to normal ...
Page 36
AD9276 600 EYE: ALL BITS 400 200 100 0 –100 –200 –400 –600 –1.5ns –1.0ns –0.5ns 0ns –200ps –100ps 0ps Figure 73. Data Eye for LVDS Outputs in ANSI-644 Mode with Trace Lengths of ...
Page 37
EYE: ALL BITS 400 200 0 –200 –400 –600 –1.5ns –1.0ns –0.5ns 0ns –200ps –100ps 0ps Figure 75. Data Eye for LVDS Outputs in ANSI-644 Mode with 100 Ω Termination On and Trace ...
Page 38
AD9276 Table 13. Flexible Output Test Modes Output Test Mode Bit Sequence Pattern Name 0000 Off (default) 0001 Midscale short 0010 +Full-scale short 0011 −Full-scale short 0100 Checkerboard 0101 PN sequence long 0110 PN sequence short 0111 One-/zero-word toggle 1000 ...
Page 39
SERIAL PORT INTERFACE (SPI) The AD9276 serial port interface allows the user to configure the signal chain for specific functions or operations through a structured register space provided inside the chip. The SPI offers the user added flexibility and customization, ...
Page 40
AD9276 During normal operation, CSB is used to signal to the device that SPI commands are to be received and processed. When CSB is brought low, the device processes SCLK and SDIO to execute instructions. Normally, CSB remains low until ...
Page 41
MEMORY MAP READING THE MEMORY MAP TABLE Each row in the memory map register table has eight bit loca- tions. The memory map is roughly divided into three sections: the chip configuration register map (Address 0x00 to Address 0x02), the ...
Page 42
AD9276 Table 18. AD9276 Memory Map Registers Addr. Bit 7 (Hex) Register Name (MSB) Bit 6 Chip Configuration Registers 0x00 chip_port_config 0 LSB first off (default) 0x01 chip_id 0x02 chip_grade X X Device Index and ...
Page 43
Addr. Bit 7 (Hex) Register Name (MSB) Bit 6 0x0F flex_channel_input Filter cutoff frequency control 0000 = 1.3 × 1/3 × f 0001 = 1.2 × 1/3 × f 0010 = 1.1 × 1/3 × f 0011 = 1.0 × ...
Page 44
AD9276 Addr. Bit 7 (Hex) Register Name (MSB) Bit 6 0x19 user_patt1_lsb B7 B6 0x1A user_patt1_msb B15 B14 0x1B user_patt2_lsb B7 B6 0x1C user_patt2_msb B15 B14 0x21 serial_control LSB first off (default) 0x22 serial_ch_stat ...
Page 45
APPLICATIONS INFORMATION POWER AND GROUND RECOMMENDATIONS When connecting power to the AD9276 recommended that two separate 1.8 V supplies be used: one for analog (AVDD) and one for digital (DRVDD). If only one 1.8 V supply is available, ...
Page 46
... SEATING 0.05 0.08 MAX PLANE COPLANARITY VIEW A ROTATED 90 ° CCW ORDERING GUIDE Model Temperature Range 1 AD9276BSVZ −40°C to +85°C 1 AD9276-65EBZ 1 AD9276-80KITZ RoHS Compliant Part. 16.00 BSC SQ 14.00 BSC SQ 100 PIN 1 TOP VIEW (PINS DOWN) ...
Page 47
NOTES Rev Page AD9276 ...
Page 48
AD9276 NOTES ©2009 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D08180-0-7/09(0) Rev Page ...