STMPE821QTR STMicroelectronics, STMPE821QTR Datasheet - Page 12
![IC CTLR TOUCH KEY 8CH CAP 16-QFN](/photos/6/64/66486/stmpe821qtr_sml.jpg)
STMPE821QTR
Manufacturer Part Number
STMPE821QTR
Description
IC CTLR TOUCH KEY 8CH CAP 16-QFN
Manufacturer
STMicroelectronics
Type
Capacitiver
Specifications of STMPE821QTR
Number Of Inputs/keys
8 Key
Data Interface
I²C
Voltage - Supply
1.65 V ~ 1.95 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-QFN
Voltage Supply Source
Single Supply
Resolution
7 bit to 10 bit
Interface Type
I2C
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2.7 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Number Of Channels
8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Sampling Rate (per Second)
-
Resolution (bits)
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
497-8826-2
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STMPE821QTR
Manufacturer:
STM
Quantity:
1 261
I2C interface
3
12/55
I
The features that are supported by the I
●
●
●
●
●
●
●
SCL/SDA level must be
Start condition
A Start condition is identified by a falling edge of SDATA while SCLK is stable at high state.
A Start condition must precede any data/command transfer. The device continuously
monitors for a Start condition and will not respond to any transaction unless one is
encountered.
Stop condition
A Stop condition is identified by a rising edge of SDATA while SCLK is stable at high state.
A Stop condition terminates communication between the slave device and bus master. A
read command that is followed by NoAck can be followed by a Stop condition to force the
slave device into idle mode. When the slave device is in idle mode, it is ready to receive the
next I
operation to registers.
Acknowledge bit (ACK)
The acknowledge bit is used to indicate a successful byte transfer. The bus transmitter
releases the SDATA after sending eight bits of data. During the ninth bit, the receiver pulls
the SDATA low to acknowledge the receipt of the eight bits of data. The receiver may leave
the SDATA in high state if it would to not acknowledge the receipt of the data.
Data Input
The device samples the data input on SDATA on the rising edge of the SCLK. The SDATA
signal must be stable during the rising edge of SCLK and the SDATA signal must change
only when SCLK is driven low.
Memory addressing
For the bus master to communicate to the slave device, the bus master must initiate a Start
condition and followed by the slave device address. Accompanying the slave device
address, there is a Read/WRITE bit (R/W). The bit is set to 1 for read and 0 for write
operation.
If a match occurs on the slave device address, the corresponding device gives an
acknowledgement on the SDA during the 9th bit time. If there is no match, it deselects itself
from the bus by not responding to the transaction.
2
C interface
I
Compliant to Philips I
Supports standard (up to 100 kbps) and fast (up to 400 kbps) modes.
7-bit and 10-bit device addressing modes
General call
Start/Restart/Stop
I
2
2
2
C slave device
C address is 0x58 (0xB0/0xB1 for write/read, including the LSB)
C transaction. A Stop condition at the end of a write command stops the write
≤
V
2
C specification version 2.1
IO
2
C interface are the following ones:
STMPE821