927837-4 TE Connectivity, 927837-4 Datasheet - Page 47

• Manufacturer Part Number: 927837-4
• Description: STD POWER TIMER
• Manufacturer: TE Connectivity
• Series: Standard Power-Timerr

Specifications of 927837-4

• Product: Terminals
• Gender: Female
• Mounting Method: Wire
• Mounting Style: Cable
• Contact Plating: Pre-Silver
• Product Type: Contact
• Mating Area Interface Dimensions (mm [in]): 4.75 x 0.81 [.187 x .032]
• Wire/cable Type: Regular Wire
• Insulation Support: With
• Wire Range (mm [awg]): 1.50-2.50² [15.5-13.5]
• Single Wire Sealing System: No
• Insulation Type: FLR (Thin Walled Cable)
• Cantilever Spring Material: Stainless Steel
• Contact Type: Socket
• Contact Base Material: CuSn4
• Contact Plating, Mating Area, Material: Pre-Silver
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant
• Accepts Wire Insulation Diameter, Range (mm [in]): 2.11 – 3.10 [0.083 – 0.122]
• Applies To: Wire/Cable
• Packaging Method: Strip
• Lead Free Status / Rohs Status: Details

108
Product Facts
■
■
■
■
■
■
■
■
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Wire-to-board connection
system combining power
and signal contacts
■
■
High conductivity copper
alloy power contacts yield
30% gain in current carrying
capacity compared to
alternative designs
Dual action contact design —
reduces mating forces by
up to 50% compared to
alternative designs
9 power and 20 signal
contacts
Positive Lock (PL) feature
on both power and signal
contacts ensures contacts
remain in position in cable
receptacle
Pin and receptacle contacts
offered in three sizes:
■
■
■
Wide 5.2 X 5.5 mm contact
spacing allows for 300V
applications.
Recognized under the
Component Program of
Underwriters Laboratories
Inc., File No. E28476
C
10A power contacts
4A signal contacts
16 AWG
18 AWG
20-22 AWG
®
US
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Power Connectors & Interconnection Systems
AMP-DUAC PL-II Connectors
The AMP-DUAC PL-II
Connectors bring both
shielding and a power /
signal mix to the popular
AMP-DUAC product family.
In addition, the wider con-
tact spacing and the use of
high conductivity materials
results in a higher current
carrying capacity than
the original 4.2 mm pitch
AMP-DUAC product.
The deep back shell allows
for gathering the larger wire
and insulation diameters
involves with combination
power / signal and shield-
ing all in the same cable.
Traditional signal connec-
tors do not accept the
range of wire sizes covered
by the AMP-DUAC PL-II
product.
For applications involving
higher voltage cabled power
distribution, this product is
the ideal solution. The
AMP-DUAC PL-II connector
uses the original industry
proven dual-action contact
design which provides a
lower mating force and less
plating wear than alternate
contact designs. The signal
contacts also feature a
twin-cantilever beam that
mates on the milled contact
surface to provide low
plating wear and high long-
term reliability.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
The cable mounted
receptacle uses the popular
“Positive Lock” devices
proven throughout the
automotive industry to
ensure all the contacts are
fully seated. The “positive
locks” are also referred to
as “terminal position
assurance”. If any one of
the contacts is not properly/
completely installed into the
housing, then the “Positive
Lock” can not be installed.
This feature reduces the
common concern of opera-
tor fatigue and the resulting
contact back-out which
occurs when a contact is
not properly seated.
The shielding system fully
encapsulates the inner
conductors and cable braids
and provides a reliable
conduction to the faceplate
of the mating equipment.
Finally, the cable retention
is accomplished through
two rear-accessed over
molded jackscrews for easy
installation and removal.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
Technical Documents
Product Specification
108-2218
Application Specification
Contact Tyco Electronics
Performance Data
Voltage Rating — 600 VAC
Current Rating —
10 Amps max on a single contact
6 Amps on each contact in 48 pos.
connector
Low Level Resistance —
10 milliohms max
Insulation Resistance —
1000 Megohms minimum
Operating Temperature —
-40°C to +105°C
Materials
Housing Material — PBT, UL 94V-0
Colors —
Plugs and Receptacles — Black
Positive Locks — White
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666