3-644615-5 TE Connectivity, 3-644615-5 Datasheet - Page 6

• Manufacturer Part Number: 3-644615-5
• Description: 05P MTA156 POL HDR ASSY LF
• Manufacturer: TE Connectivity

Specifications of 3-644615-5

• Connector Type: Header
• Product Line: MTA-156
• Pcb Mounting Orientation: Vertical
• Pcb Mount Retention: With
• Mating Connector Lock: With
• Four Points Of Contact: Without
• Shrouded: No
• Mounting Ears: Without
• Mating Connector Lock Type: Polarized Lock
• Pcb Mount Alignment Type: Polarized Retention Peg
• Post Size (mm [in]): 1.14 [.045]
• Panel Mount Retention: Without
• Current Rating (a): 7
• Voltage Rating (vac): 600
• Solder Tail Contact Plating: Tin
• Termination Post Length (mm [in]): 3.18 [0.125]
• Number Of Positions: 5
• Centerline (mm [in]): 3.96 [0.156]
• Narrow: No
• Post Number(s) Omitted: None
• Pcb Mount Retention Type: Boardlock(s)
• Contact Type: Pin
• Contact Shape: Square
• Contact Plating, Mating Area, Material: Tin
• Contact Base Material: Copper Alloy
• Connector Style: Plug
• Housing Color: White
• Mating Alignment: With
• Ul Flammability Rating: UL 94V-0
• Housing Material: Polyester
• Backwall/post Interruption(s): Without
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
• Rohs/elv Compliance History: Always was RoHS compliant
• Applies To: Printed Circuit Board
• Application Use: Wire-to-Board

4.
4.1.
4.2.
4.3.
4.4.
Rev J
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
B.
Requalification Testing
If changes significantly affecting form, fit or function are made to the product or manufacturing process,
product assurance shall coordinate requalification testing, consisting of all or part of the original testing
sequence as determined by development/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product meets requirements of Figure 1. Failures attributed
to equipment, test setup or operator deficiencies shall not disqualify the product. If product failure
occurs, corrective action shall be taken and samples resubmitted for qualification. Testing to confirm
corrective action is required before resubmittal.
Quality Conformance Inspection
The applicable quality inspection plan will specify the sampling acceptable quality level to be used.
Dimensional and functional requirements shall be in accordance with the applicable product drawing
and this specification.
Sample Selection
Samples shall be prepared in accordance with applicable Instruction Sheets and shall be selected
at random from current production. Unless otherwise required for the test procedure, test groups 1,
2, 3 and 4 shall consist of mated pairs of MTA 156 connectors and headers. Test group 1 shall
consist of 5, 6 position standard tin plated samples; 5, 6 position high force tin plated samples; and
5, 6 position gold plated samples. All samples shall be terminated to the maximum wire size and
mounted on printed circuit board PN 93-660164. Test group 2 shall consist of 3, 10 position
standard tin plated samples terminated to 26 AWG wire and mounted on printed circuit board PN
93-660273-000; and 3, 10 position standard tin plated samples terminated to 18 AWG wire and
mounted on printed circuit board PN 93-660092-000. Test group 3 shall consist of 5 unmated and
unmounted 24 position standard tin plated samples terminated to maximum wire size. Test group
4 shall consist of 5, 10 position gold plated samples terminated to 22 AWG wire and mounted on
printed circuit board PN 93-660164. Test group 5 shall consist of 6, 10 position standard tin plated
samples terminated to minimum wire size; and 6, 10 position standard tin plated samples
terminated to maximum wire size. Test group 6 shall consist of 5, 6 position .156 tin plated
headers.
Test Sequence
Qualification inspection shall be verified by testing samples as specified in Figure 2.
108-1051
6 of 10