MCP3423-E/UN Microchip Technology, MCP3423-E/UN Datasheet - Page 13

• Manufacturer Part Number: MCP3423-E/UN
• Description: IC ADC 18BIT 3.75SPS 2CH 10-MSOP
• Manufacturer: Microchip Technology

Specifications of MCP3423-E/UN

• Data Interface: I²C, Serial
• Number Of Bits: 18
• Sampling Rate (per Second): 3.75
• Number Of Converters: 1
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 10-TFSOP (0.118", 3.00mm Width)
• Resolution (bits): 18bit
• Sampling Rate: 3.75SPS
• Input Channel Type: Differential
• Supply Voltage Range - Analog: 2.7V To 5.5V
• Supply Current: 145µA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCP3423EV - BOARD EVAL 18BIT 2CH ADC MCP3423
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

4.0
4.1
The MCP3422/3/4 devices are differential multi-
channel low-power, 18-Bit Delta-Sigma A/D converters
with an I
input
programmable gain amplifier (PGA), an on-board
voltage reference (2.048V), and an internal oscillator.
When the device powers up (POR is set), it
automatically resets the configuration bits to default
settings.
Device default settings are:
• Conversion bit resolution: 12 bits (240 sps)
• Input channel: Channel 1
• PGA gain setting: x1
• Continuous conversion
Once the device is powered-up, the user can
reprogram the configuration bits using I
interface any time. The configuration bits are stored in
volatile memory.
User selectable options are:
• Conversion bit resolution: 12, 14, 16, or 18 bits
• Input channel selection: CH1, CH2, CH3, or CH4.
• PGA Gain selection: x1, x2, x4, or x8
• Continuous or one-shot conversion
In the Continuous Conversion mode, the device
converts the inputs continuously. While in the One-Shot
Conversion mode, the device converts the input one
time and stays in the low-power standby mode until it
receives another command for a new conversion.
During the standby mode, the device consumes less
than 1 µA maximum.
4.2
The device contains an internal Power-On-Reset
(POR) circuit that monitors power supply voltage (V
during operation. This circuit ensures correct device
start-up at system power-up and power-down events.
The device resets all configuration register bits to
default settings as soon as the POR is set.
The POR has built-in hysteresis and a timer to give a
high degree of immunity to potential ripples and noises
on the power supply. A 0.1 µF decoupling capacitor
should be mounted as close as possible to the V
for additional transient immunity.
© 2009 Microchip Technology Inc.
channel
DESCRIPTION OF DEVICE
OPERATION
General Overview
Power-On-Reset (POR)
2
C serial interface. The devices contain an
selection
multiplexer
(mux),
2
C serial
DD
DD
pin
a
)
The threshold voltage is set at 2.2V with a tolerance of
approximately ±5%. If the supply voltage falls below
this threshold, the device will be held in a reset
condition. The typical hysteresis value is approximately
200 mV.
The POR circuit is shut-down during the low-power
standby mode. Once a power-up event has occurred,
the
(approximately 300 µs) before a conversion takes
place. During this time, all internal analog circuitries are
settled before the first conversion occurs.
illustrates the conditions for power-up and power-down
events under typical start-up conditions.
FIGURE 4-1:
4.3
The device contains an on-board 2.048V voltage
reference. This reference voltage is for internal use
only and not directly measurable. The specification of
the reference voltage is part of the device’s gain and
drift specifications. Therefore, there is no separate
specification for the on-board reference.
4.4
The user can select the input channel using the
configuration register bits. Each channel can be used
for differential or single-ended input.
Each input channel has a switched capacitor input
structure. The internal sampling capacitor (3.2 pF for
PGA = 1) is charged and discharged to process a
conversion. The charging and discharging of the input
sampling capacitor creates dynamic input currents at
each input pin. The current is a function of the
differential input voltages, and inversely proportional to
the internal sampling capacitance, sampling frequency,
and PGA setting.
V
2.2V
2.0V
DD
device
Reset Start-up
Internal Voltage Reference
Analog Input Channels
300 µS
requires
MCP3422/3/4
Normal Operation
POR Operation.
additional
DS22088C-page 13
Reset
delay
Figure 4-1
Time
time