X1226V8 Intersil, X1226V8 Datasheet - Page 17

• Manufacturer Part Number: X1226V8
• Description: IC RTC/CALENDAR/4K EE 8-TSSOP
• Manufacturer: Intersil
• Type: Clock/Calendar/EEPROMr

Specifications of X1226V8

• Memory Size: 4K (512 x 8)
• Time Format: HH:MM:SS (12/24 hr)
• Date Format: YY-MM-DD-dd
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 8-TSSOP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Notes: (1) The device enters the Active state after any start, and remains active: for 9 clock cycles if the Device Select Bits in the Slave Address
Capacitance T
Notes: (1) This parameter is not 100% tested.
AC CHARACTERISTICS
AC Test Conditions
Figure 14. Standard Output Load for testing the device with V
Input Pulse Levels
Input Rise and Fall Times
Input and Output Timing
Levels
Output Load
Symbol
C
Equivalent AC Output Load Circuit for V
C
OUT
IN
(2) The device enters the Program state 200nS after a stop ending a write operation and continues for t
(3) The device goes into the Timekeeping state 200nS after any stop, except those that initiate a nonvolatile write cycle; t
(4) For reference only and not tested.
(5) V
(6) V
(7) V
(8) V
(9) V
(10) V
(11) I
(12) I
(13) Threshold voltages based on the higher of Vcc or Vback.
(14) Using recommended crystal and oscillator network applied to X1 and X2 (25°C).
(15) Typical values are for T
(2) The input capacitance between x1 and x2 pins can be varied between 5pF and 19.75pF by using analog trimming registers
(1)
(1)
SDA
that initiates a nonvolatile write cycle; or 9 clock cycles after any start that is not followed by the correct Device Select Bits in the Slave
Address Byte.
Byte are incorrect or until 200nS after a stop ending a read or write operation.
OL
OH
IL
CC
BACK
SDA
SDA
SDA
= V
= 3.0mA at 5.5V, 1.5mA at 2.7V
= -1.0mA at 5.5V, -0.4mA at 2.7V
= 0V
Output Capacitance (SDA, PHZ/IRQ)
Input Capacitance (SCL)
= V
=V
= GND or V
A
CC
= 0V
= 25°C, f = 1.0 MHz, V
SCL
SCL
x 0.1, V
=V
5.0V
=V
BACK
CC
CC
IH
, Others = GND or V
1533Ω
100pF
17
, Others = GND or V
, V
= V
SCL
A
CC
= 25°C
x 0.9, f
= GND or V
V
10ns
V
Standard Output Load
Parameter
CC
CC
For V
and I
SCL
x 0.1 to V
x 0.5
OL
OL
CC
= 400KHz
CC
CC
= 0.4V
= 3 mA
BACK
CC
= 5V
= 5V
CC
x 0.9
X1226
PHZ/IRQ
CC
Max.
10
10
= 5.0V
5.0V
Units
pF
pF
1316Ω
806Ω
WC
.
100pF
Test Conditions
V
V
OUT
IN
= 0V
= 0V
WC
after a stop
May 8, 2006
FN8098.3