ISL1218IUZ-T Intersil, ISL1218IUZ-T Datasheet - Page 12

• Manufacturer Part Number: ISL1218IUZ-T
• Description: IC RTC LP BATT BACKED SRAM 8MSOP
• Manufacturer: Intersil
• Type: Clock/Calendar/NVSRAMr

Specifications of ISL1218IUZ-T

• Memory Size: 8B
• Time Format: HH:MM:SS (12/24 hr)
• Date Format: YY-MM-DD-dd
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

NOTE: Writing to register 08h has restrictions. If V
byte writes to register 08h are allowed, only page writes beginning
with register 07h. If V
allowed, as well as page writes.
FREQUENCY OUT CONTROL BITS (FO <3:0>)
These bits enable/disable the frequency output function and
select the output frequency at the IRQ/F
Table 4 for frequency selection. When the frequency mode is
enabled, it will override the alarm mode at the IRQ/F
FREQUENCY OUTPUT AND INTERRUPT BIT (FOBATB)
This bit enables/disables the F
backup mode (i.e. V
FOBATB is set to “1” the F
battery backup mode. This means that both the frequency
output and alarm output functions are disabled. When the
FOBATB is cleared to “0”, the F
during battery backup mode.
LOW POWER MODE BIT (LPMODE)
This bit enables/disables low power mode. With
LPMODE = “0”, the device will be in normal mode and the
V
V
power mode and the V
V
about 600nA when using LPMODE = “1” with V
(See Typical Performance Curves: I
LPMODE ON and OFF.)
FREQUENCY,
BAT
DD
DD
32768
F
< V
< V
4096
1024
1/16
1/32
supply will be used when V
1/2
1/4
1/8
OUT
64
32
16
TABLE 4. FREQUENCY SELECTION OF F
0
8
4
2
1
TRIP
BAT
. With LPMODE = “1”, the device will be in low
- V
UNITS
BATHYS
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
DD
BAT
>V
BAT
BAT
. There is a supply current saving of
power source active). When the
FO3
OUT
, then a byte write to register 08h IS
supply will be used when
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
12
OUT
/IRQ pin is disabled during
OUT
DD
/IRQ pin during battery
DD
/IRQ pin is enabled
FO2
< V
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
vs V
OUT
BAT
CC
BAT
- V
pin. See
FO1
OUT
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
>V
DD
with
BATHYS
DD
PIN
= 5V.
OUT
, then no
FO0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
and
pin.
ISL1218
It should be noted that any writes to the LPMODE bit that
may put the device into Low Power Mode should be avoided
if V
the I
ALARM ENABLE BIT (ALME)
This bit enables/disables the alarm function. When the ALME
bit is set to “1”, the alarm function is enabled. When the ALME
is cleared to “0”, the alarm function is disabled. The alarm
function can operate in either a single event alarm or a periodic
interrupt alarm (see IM bit).
NOTE: When the frequency output mode is enabled, the alarm function
is disabled.
INTERRUPT/ALARM MODE BIT (IM)
This bit enables/disables the interrupt mode of the alarm
function. When the IM bit is set to “1”, the alarm will operate
in the interrupt mode, where an active low pulse width of
250ms will appear at the IRQ/F
triggered by the alarm as defined by the alarm registers (0Ch
to 11h). When the IM bit is cleared to “0”, the alarm will
operate in standard mode, where the IRQ/F
tied low until the ALM status bit is cleared to “0”.
Analog Trimming Register
ANALOG TRIMMING REGISTER (ATR<5:0>)
Six analog trimming bits, ATR0 to ATR5, are provided in
order to adjust the on-chip load capacitance value for
frequency compensation of the RTC. Each bit has a different
weight for capacitance adjustment. For example, using a
Citizen CFS-206 crystal with different ATR bit combinations
provides an estimated ppm adjustment range from -34 to
+80ppm to the nominal frequency compensation. The
combination of analog and digital trimming can give up to -94
to +140ppm of total adjustment.
DD
2
C interface (until V
IM BIT
<V
0
1
BAT
, as the device will no longer communicate over
X1
X2
FIGURE 11. DIAGRAM OF ATR
Single Time Event Set By Alarm
Repetitive/Recurring Time Event Set By Alarm
C
C
X1
X2
INTERRUPT/ALARM FREQUENCY
DD
rises above V
OUT
OSCILLATOR
pin when the RTC is
CRYSTAL
BAT
OUT
).
pin will be
June 22, 2006
FN6313.0