PCF2129AT/1,518 NXP Semiconductors, PCF2129AT/1,518 Datasheet - Page 12

• Manufacturer Part Number: PCF2129AT/1,518
• Description: IC RTC /CALENDAR TCXO QTZ 20SOIC
• Manufacturer: NXP Semiconductors
• Type: Clock/Calendar/Alarmr

Specifications of PCF2129AT/1,518

• Package / Case: 20-SOIC (7.5mm Width)
• Time Format: HH:MM:SS (12/24 hr)
• Date Format: YY-MM-DD-dd
• Interface: I²C, SPI
• Voltage - Supply: 1.8 V ~ 4.2 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Function: Clock/Calendar
• Supply Voltage (max): 4.2 V
• Supply Voltage (min): 1.8 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Rtc Bus Interface: Serial (3-Wire, I2C, SPI)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 935288599518

NXP Semiconductors
PCF2129A_2
Product data sheet
8.3.1.1 Temperature measurement
8.3.1 Temperature compensated crystal oscillator
8.3.2 Clock output
8.3 Register CLKOUT_ctl
Table 8.
The frequency of tuning fork quartz crystal oscillators is temperature-dependent. In the
PCF2129A the frequency drift caused by temperature variation is corrected by adjusting
the load capacitance of the crystal oscillator.
The load capacitance is changed by switching between two load capacitance values using
a modulation signal with a programmable duty cycle. Every chip is calibrated in order to
produce, at the measured temperature, the correct duty cycle which compensates for the
frequency drift.
The frequency accuracy can be evaluated by measuring the frequency of the square
wave signal available at the output pin CLKOUT. However, the selection of
f
accurate frequency measurement occurs when f
The PCF2129A has a temperature sensor circuit used to perform the temperature
compensation of the frequency. The temperature is measured immediately after power-on
and then periodically with a period set by the temperature conversion rate TCR[1:0] in the
register CLKOUT_ctl.
Table 9.
[1]
A programmable square wave is available at pin CLKOUT. Operation is controlled by the
COF[2:0] control bits in register CLKOUT_ctl. Frequencies of 32.768 kHz (default) down
to 1 Hz can be generated for use as a system clock, microcontroller clock, input to a
charge pump, or for calibration of the oscillator.
CLKOUT is an open-drain output and enabled at power-on. When disabled, the output is
high-impedance.
The duty cycle of the selected clock is not controlled, however, due to the nature of the
clock generation all but the 32.768 kHz frequencies will be 50 : 50.
Bit
7 to 6 TCR[1:0]
5 to 3 -
2 to 0 COF[2:0]
TCR[1:0]
00
01
10
11
CLKOUT
Default value.
Symbol
= 32.768 kHz (default value) leads to inaccurate measurements. The most
CLKOUT_ctl - CLKOUT control register (address 0Fh) bit description
Temperature measurement period
All information provided in this document is subject to legal disclaimers.
[1]
Rev. 02 — 7 May 2010
Temperature measurement period
4 min
2 min
1 min
30 seconds
Value
see
-
see
Table 9
Table 10
Description
temperature measurement period
unused
CLKOUT frequency selection
Integrated RTC, TCXO and quartz crystal
CLKOUT
= 1 Hz is selected (see
PCF2129A
© NXP B.V. 2010. All rights reserved.
Table
12 of 69
10).