M48T58-70PC1 STMicroelectronics, M48T58-70PC1 Datasheet - Page 15
![IC TIMEKPR NVRAM 64KBIT 5V 28-DI](/photos/6/58/65819/m48t58-70pc1_sml.jpg)
M48T58-70PC1
Manufacturer Part Number
M48T58-70PC1
Description
IC TIMEKPR NVRAM 64KBIT 5V 28-DI
Manufacturer
STMicroelectronics
Series
Timekeeper®r
Type
Clock/Calendar/NVSRAMr
Datasheet
1.M48T58-70PC1.pdf
(33 pages)
Specifications of M48T58-70PC1
Memory Size
64K (8K x 8)
Time Format
HH:MM:SS (24 hr)
Date Format
YY-MM-DD-dd
Interface
Parallel
Voltage - Supply
4.75 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Through Hole
Package / Case
28-DIP Module (600 mil), 28-EDIP
Function
Clock/Calendar/NV Timekeeping RAM/Battery Backup
Rtc Memory Size
8192 Byte
Supply Voltage (max)
5.5 V
Supply Voltage (min)
4.75 V
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Mounting Style
Through Hole
Rtc Bus Interface
Parallel
Clock Format
HH
Clock Ic Type
Timekeeper
Memory Configuration
8K X 8
Supply Voltage Range
4.75V To 5.5V
Digital Ic Case Style
DIP
No. Of Pins
28
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-2857-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M48T58-70PC1
Manufacturer:
NS
Quantity:
290
Company:
Part Number:
M48T58-70PC1
Manufacturer:
XILINX
Quantity:
86
Part Number:
M48T58-70PC1
Manufacturer:
ST
Quantity:
20 000
M48T58, M48T58Y
6
6.1
6.2
6.3
Clock operations
Reading the clock
Updates to the TIMEKEEPER
read to prevent reading data in transition. The BiPORT™ TIMEKEEPER cells in the RAM
array are only data registers and not the actual clock counters, so updating the registers can
be halted without disturbing the clock itself.
Updating is halted when a '1' is written to the READ bit, D6 in the control register 1FF8h. As
long as a '1' remains in that position, updating is halted.
After a halt is issued, the registers reflect the count; that is, the day, date, and the time that
were current at the moment the halt command was issued.
All of the TIMEKEEPER registers are updated simultaneously. A halt will not interrupt an
update in progress. Updating is within a second after the bit is reset to a '0.'
Setting the clock
Bit D7 of the control register (1FF8h) is the WRITE bit. Setting the WRITE bit to a '1,' like the
READ bit, halts updates to the TIMEKEEPER
the correct day, date, and time data in 24-hour BCD format (see
WRITE bit to a '0' then transfers the values of all time registers (1FF9h-1FFFh) to the actual
TIMEKEEPER counters and allows normal operation to resume. The bits marked as '0' in
Table 5 on page 16
operation. After the WRITE bit is reset, the next clock update will occur within one second.
See the application note AN923 “TIMEKEEPER Rolling Into the 21st Century” for
information on century rollover.
Stopping and starting the oscillator
The oscillator may be stopped at any time. If the device is going to spend a significant
amount of time on the shelf, the oscillator can be turned off to minimize current drain on the
battery. The STOP bit is the MSB of the seconds register. Setting it to a '1' stops the
oscillator. The M48T58/Y is shipped from STMicroelectronics with the STOP bit set to a '1.'
When reset to a '0,' the M48T58/Y oscillator starts within 1 second.
must be written to '0' to allow for normal TIMEKEEPER and RAM
®
Doc ID 2412 Rev 7
registers (see
®
Table
registers. The user can then load them with
5) should be halted before clock data is
Table
5). Resetting the
Clock operations
15/33