CY2XF23FLXCT Cypress Semiconductor Corp, CY2XF23FLXCT Datasheet - Page 3

• Manufacturer Part Number: CY2XF23FLXCT
• Description: IC XTAL OSC LVDS I2C 6CLCC
• Manufacturer: Cypress Semiconductor Corp

Specifications of CY2XF23FLXCT

• Pll: Yes
• Input: Crystal
• Output: LVDS
• Number Of Circuits: 1
• Ratio - Input:output: 1:1
• Differential - Input:output: No/Yes
• Frequency - Max: 690MHz
• Divider/multiplier: Yes/No
• Voltage - Supply: *
• Operating Temperature: *
• Mounting Type: Surface Mount
• Package / Case: 6-CLCC
• Frequency: *
• Count: *
• Operating Supply Voltage (typ): 2.5/3.3
• Output Level: LVDS
• Symmetry Max: 60%
• Operating Temp Range: 0C to 70C
• Screening Level: Commercial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Standard and Application-Specific Factory Configurations
Functional Description
The CY2XF23 is a PLL-based high-performance clock
generator. It uses an internal crystal oscillator as a reference,
and outputs one differential LVDS clock. It has an I
interface
The CY2XF23 comes configured for four different frequencies.
At power-on, the four configurations are transparently loaded
into an internal volatile memory which, in turn, controls the PLL.
The user can switch between the four frequencies through the
I
output frequencies by shifting new data into the internal memory.
Frequency margining is a common application for this feature.
One frequency is used for the standard operating mode of the
device, while additional frequencies are available for margin
testing, either during product development or in-system
manufacturing test.
Note that all configuration changes made using I
temporary and are lost when power is removed from the device.
At power-on, the device returns to its original state.
The configuration for a particular frequency is stored in a 6-byte
block of memory, known as a word. The CY2XF23 has four such
words, labeled ‘Frequency Word 0’ through ‘Frequency Word 3’.
An additional register byte contains a 2-bit field, which selects
one of the four frequency words. By writing to this select byte,
the user can switch back and forth between the four programmed
frequencies. The select byte can be configured to select any of
the four frequency words at power-on.
When changing the output frequency, the frequency transition is
not guaranteed to be smooth. There can be frequency
excursions beyond the start frequency and the new frequency.
Glitches and runt pulses are possible, and time must be allowed
for the PLL to re-lock.
If more than four frequencies are needed, the I
used to change any of the four frequency words. When writing
frequency words through I
currently selected word. Instead, write one of the three
unselected words before changing the select byte to select that
new word.
Figure 2
selected.
Document Number: 001-53145 Rev. *D
CY2XF23LXC001T
CY2XF23LXI625T
2
Note
1. The serial interface is I
C bus. The user can also configure the CY2XF23 with new
setup time, and output hold time.
Part Number
[1]
shows how the frequency words are arranged and
, which is used to change the output frequency.
2
C Bus compliant, with the following exceptions: SDA input leakage current, SDA input capacitance, SDA and SCLK are clamped to V
2
100.00 MHz (default)
625.00 MHz (default)
C, users should not change the
Output Frequency
103.000007 MHz
104.999993 MHz
78.125 MHz
156.25 MHz
312.50 MHz
95.00 MHz
2
C bus can be
PRELIMINARY
2
C bus serial
Frequency Word
2
C are
0
1
2
3
0
1
2
3
Figure 2. Frequency Words
Configuration Software
Cypress provides
to create data values for shifting into the frequency words. This
software is required because the algorithm is too complicated to
be described here.
The user specifies the output frequency. The software then
calculates the bit stream for up to four frequency words, as
outlined by the register addresses for each word seen in
Figure
Programming Description
The CY2XF23 is a programmable device. Before being used in
an application, it must be programmed with the output
frequencies and other variables described in
Variables
each with its own programming flow. They are described in the
following sections.
Field-Programmable CY2XF23F
Field programmable devices are shipped unprogrammed and
must be programmed before being installed on a printed circuit
board (PCB). Customers use
specify the device configuration and generate a joint electron
devices
programming file. Programming of samples and prototype
quantities is available using the CyClockWizard software along
with a
Kit
added distribution partners also provide programming services.
Field programmable devices are designated with an ‘F’ in the
part number. They are intended for quick prototyping and
inventory reduction. The software and programmer kit hardware
can be downloaded from
hyperlinks above.
16h – 1Bh
1Ch – 21h
10h – 15h
22h – 27h
Register
Address
40h
with a
CY3675-CLKMAKER1 CyClockMaker Clock Programmer
2.
on page 4. Two different device types are available,
Select Byte
engineering
CY3675-LCC6A socket
1.875 MHz to 20 MHz
1.875 MHz to 20 MHz
1.875 MHz to 20 MHz
1.875 MHz to 20 MHz
637 kHz to 10 MHz
637 kHz to 10 MHz
637 kHz to 10 MHz
637 kHz to 10 MHz
Offset Range
Frequency Word 0
Frequency Word 1
Frequency Word 2
Frequency Word 3
CyClockWizard™
RMS Phase Jitter (Random)
council
www.cypress.com
Bits [1:0]
CyClockWizard™
software that enables users
adapter. Cypress’s value
(JEDEC - extension .jed)
00
01
10
11
Sel
Jitter (Typical)
CY2XF23
by clicking the
0.52 ps
0.37 ps
0.31 ps
0.29 ps
0.31 ps
Control
Programming
Page 3 of 14
–
–
–
software to
DD
PLL
,
[+] Feedback