ADF4218LBRU-REEL Analog Devices Inc, ADF4218LBRU-REEL Datasheet - Page 10

• Manufacturer Part Number: ADF4218LBRU-REEL
• Description: IC PLL FREQ SYNTHESIZER 20-TSSOP
• Manufacturer: Analog Devices Inc
• Type: Clock/Frequency Synthesizer (RF/IF)r

Specifications of ADF4218LBRU-REEL

• Rohs Status: RoHS non-compliant
• Pll: Yes
• Input: CMOS
• Output: Clock
• Number Of Circuits: 1
• Ratio - Input:output: 3:1
• Differential - Input:output: Yes/No
• Frequency - Max: 3GHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 2.6 V ~ 3.3 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-TSSOP
• Frequency-max: 3GHz

ADF4217L/ADF4218L/ADF4219L
The A and B counters, in conjunction with the dual modulus
prescaler, make it possible to generate output frequencies that
are spaced only by the Reference Frequency divided by R. The
equation for the VCO frequency is as follows:
f
P
B
A
f
R
R COUNTER
The 14-bit R counter allows the input reference frequency to be
divided down to produce the reference clock to the phase frequency
detector (PFD). Division ratios from 1 to 16,383 are allowed. The
extra R15 bit on the ADF4219L allows ratios from 1 to 32767.
PHASE FREQUENCY DETECTOR (PFD) AND
CHARGE PUMP
The PFD takes inputs from the R counter and N counter and
produces an output proportional to the phase and frequency
difference between them. Figure 5 is a simplified schematic.
CP OUTPUT
VCO
REF
R DIVIDER
N DIVIDER
IN
R DIVIDER
N DIVIDER
= Output frequency of external voltage controlled oscillator
= Preset modulus of dual modulus prescaler (8/9, 16/17, and
= Preset divide ratio of binary 11-bit counter (ADF4217L/
= Preset divide ratio of binary 6-bit A counter (ADF4217L/
= Output frequency of the external reference frequency
= Preset divide ratio of binary 14-bit programmable reference
(VCO).
so on).
ADF4218L), binary 13-bit counter (ADF4219L).
ADF4218L), binary 5-bit counter (ADF4219L).
oscillator.
counter (1 to 16383). The ADF4219L has an R divide
of 15 bits.
Figure 5. PFD Simplified Schematic
HI
HI
f
VCO
D1
D2
CLR1
CLR2
U1
U2
=
Q1
Q2
[
(
ELEMENT
P B
UP
DELAY
DOWN
×
)
+
A
U3
]
×
f
REF
IN
/
CPGND
R
V
P
CHARGE
PUMP
CP
–10–
MUXOUT AND LOCK DETECT
The output multiplexer on the ADF4217L family allows the user
to access various internal points on the chip. The state of MUXOUT
is controlled by P3, P4, P11, and P12. See Tables IV and VII.
Figure 6 shows the MUXOUT section in block diagram form.
IF/RF ANALOG LOCK DETECT
Lock Detect
MUXOUT can be programmed for analog lock detect. The
N-channel open-drain analog lock detect should be operated
with an external pull-up resistor of 10 kΩ nominal. When lock
has been detected, it is high with narrow low going pulses.
INPUT SHIFT REGISTER
The functional block diagram for the ADF4217L family is shown
on page 1. The main blocks include a 22-bit input shift register,
a 14-bit R counter, and an N counter. The N counter is comprised
of a 6-bit A counter and an 11-bit B counter for the ADF4217L
and the ADF4218L. The 18-bit N counter on the ADF4219L
is comprised of a 13-bit B counter and a 5-bit A counter. Data
is clocked into the 22-bit shift register on each rising edge of
CLK. The data is clocked in MSB first. Data is transferred from
the shift register to one of four latches on the rising edge of LE.
The destination latch is determined by the state of the two con-
trol bits (C2, C1) in the shift register. These are the two LSBs,
DB1 and DB0, as shown in the timing diagram of Figure 1. The
truth table for these bits is shown in Table I.
Control Bits
C2
0
0
1
1
RF ANALOG LOCK DETECT
IF ANALOG LOCK DETECT
RF R COUNTER OUTPUT
RF N COUNTER OUTPUT
IF R COUNTER OUTPUT
IF N COUNTER OUTPUT
C1
0
1
0
1
Data Latch
IF R Counter
IF AB Counter (and Prescaler Select)
RF R Counter
RF AB Counter (and Prescaler Select)
Figure 6. MUXOUT Circuit
Table I. C2, C1 Truth Table
MUX
CONTROL
DGND
DV
DD
REV. C
MUXOUT