ICS650R-21ILF IDT, Integrated Device Technology Inc, ICS650R-21ILF Datasheet - Page 3
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
ICS650R-21ILF
Manufacturer Part Number
ICS650R-21ILF
Description
IC CLK SOURCE SYSTEM PER 20-SSOP
Manufacturer
IDT, Integrated Device Technology Inc
Type
Clock/Frequency Synthesizerr
Datasheet
1.ICS650R-21LFT.pdf
(8 pages)
Specifications of ICS650R-21ILF
Pll
Yes
Input
Clock, Crystal
Output
CMOS
Number Of Circuits
1
Ratio - Input:output
1:8
Differential - Input:output
No/No
Frequency - Max
66.67MHz
Divider/multiplier
No/No
Voltage - Supply
3 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
20-SSOP
Frequency-max
67MHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
650R-21ILF
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ICS650R-21ILF
Manufacturer:
SMI
Quantity:
7 385
External Components
The ICS650-21 requires a minimum number of external
components for proper operation.
Decoupling Capacitor
Decoupling capacitors of 0.01µF must be connected
between each VDD and GND (pins 4 and 6, pins 16 and 14),
as close to the device as possible. For optimum device
performance, the decoupling capacitor should be mounted
on the component side of the PCB. Avoid the use of vias in
the decoupling circuit.
Series Termination Resistor
When the PCB trace between the clock outputs and the
loads are over 1 inch, series termination should be used. To
series terminate a 50 trace (a commonly used trace
IDT™ / ICS™ SYSTEM PERIPHERAL CLOCK SOURCE
Number
ICS650-21
SYSTEM PERIPHERAL CLOCK SOURCE
Pin
13
14
15
16
17
18
19
20
OFF/14.318M
PCLK3
PCLK2
PSEL0
PSEL1
Name
ASEL
GND
VDD
Pin
Output
Output
Output
Power
Power
Type
Input
Input
Input
Pin
14.31818 MHz clock output only when ASEL = VDD.
Connect to ground.
ACLK select pin. Determines frequency of audio clock per table above.
Connect to VDD. Must be same value as other VDD. Decouple with pin 14.
PCLK output number 3 per table above.
PCLK output number 2 per table above.
Processor select pin #0. Determines frequencies on PCLKs 1-3 per table
above.
Processor select pin #1. Determines frequencies on PCLKs 1-3 per table
above.
3
impedance) place a 33 resistor in series with the clock line,
as close to the clock output pin as possible. The nominal
impedance of the clock output is 20 .
Crystal Information
The crystal used should be a fundamental mode (do not use
third overtone), parallel resonant. Crystal capacitors should
be connected from pins X1 to ground and X2 to ground to
optimize the initial accuracy. The value of these capacitors
is given by the following equation:
In the equation, C
crystal with a 16pF load capacitance, two 20 pF [(16-6) x 2]
capacitors should be used.
Pin Description
Crystal caps (pF) = (C
L
is the crystal load capacitance. So, for a
L
- 6) x 2
ICS650-21
CLOCK SYNTHESIZER
REV J 051310