SI5338A-A-GM Silicon Laboratories Inc, SI5338A-A-GM Datasheet - Page 19
![IC CLK GEN QUAD 700MHZ 24-QFN](/photos/6/55/65598/si5338a-a-gm_sml.jpg)
SI5338A-A-GM
Manufacturer Part Number
SI5338A-A-GM
Description
IC CLK GEN QUAD 700MHZ 24-QFN
Manufacturer
Silicon Laboratories Inc
Type
Clock Generatorr
Datasheet
1.SI5338B-A-GM.pdf
(42 pages)
Specifications of SI5338A-A-GM
Pll
Yes
Input
CML, HCSL, HSCL, LVDS, LVPECL, Crystal
Output
CMOS, HCSL. HSTL. LVDS. LVPECL. SSTL
Number Of Circuits
1
Ratio - Input:output
3:4
Differential - Input:output
Yes/Yes
Frequency - Max
700MHz
Divider/multiplier
Yes/Yes
Voltage - Supply
1.71 V ~ 3.63 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
24-QFN
Frequency-max
700MHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
336-1747 - KIT PROG FIELD SI5338/4/0336-1556 - BOARD EVALUATION SI5338
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1553-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
SI5338A-A-GM
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
3.4. Output Stage
The output stage consists of output selectors, output
dividers, and programmable output drivers as shown in
Figure 7.
The output selectors select the clock source for the
output drivers. By default, each output driver is
connected to its own MultiSynth block (e.g. MS0 to
CLK0, MS1 to CLK1, etc), but other combinations are
possible by reconfiguring the device. The PLL can be
bypassed by connecting the input stage signals (osc,
ref, refdiv, fb, or fbdiv) directly to the output divider.
Bypassing an input directly to an output will not allow
phase alignment of that output to other outputs. Each of
the output drivers can also connect to the first
MultiSynth block (MS0) enabling a fan-out function. This
allows the Si5338 to act as a clock generator, a fanout
buffer, or a combination of both in the same package.
The output dividers (R0, R1, R2, R3) allow another
stage of clock division.These dividers are configurable
as divide by 1 (default), 2, 4, 8, 16, or 32. When an Rn
does not equal 1, the phase alignment function for that
output will not work.
The output drivers are configurable to support common
signal formats, such as LVPECL, LVDS, HCSL, CMOS,
HSTL, and SSTL. Separate output supply pins (VDDO
are provided for each output buffer.
The voltage on these supply pins can be 3.3, 2.5, 1.8, or
1.5 V as needed for the possible output formats.
Additionally, the outputs can be configured to stop high,
low, or tri-state when the PLL has lost lock. If the Si5338
is used in a zero delay mode, the output that is fed back
must be set for always on, which will override any
output disable signal.
Figure 7. Output Stage
Output
Stage
÷
÷
÷
÷
R0
R1
R2
R3
VDDO0
CLK0A
CLK0B
VDDO1
CLK1A
CLK1B
VDDO2
CLK2A
CLK2B
VDDO3
CLK3A
CLK3B
Rev. 1.0
n
)
Each of the outputs can also be enabled or disabled
through the I
outputs is available in the Si5338K/L/M.
3.5. Configuring the Si5338
The Si5338 is a highly-flexible clock generator that is
entirely configurable through its I
device’s default configuration is stored in non-volatile
memory (NVM) as shown in Figure 8. The NVM is a
one-time programmable memory (OTP), which can
store a custom user configuration at power-up. This is a
useful feature for applications that need a clock present
at power-up (e.g., for providing a clock to a processor).
During a power cycle or a power-on reset (POR), the
contents of the NVM are copied into random access
memory (RAM), which sets the device configuration that
will be used during operation. Any changes to the
device configuration after power-up are made by
reading and writing to registers in the RAM space
through the I
"3.1.1. ClockBuilder™ Desktop Software" on page 16)
can be used to easily configure register map files that
can be written into RAM (see “3.5.2. Creating a New
Configuration for RAM” for details). Alternatively, the
register map file can be created manually with the help
of the equations in AN411.
Two versions of the Si5338 are available. First,
standard, non-customized Si5338 devices are available
in which the RAM can be configured in-circuit via I
(example part number Si5338C-A-GM). Alternatively,
standard Si5338 devices can be field-programmed
using the Si5338/56-PROG-EVB field programmer.
Second, custom factory-programmed Si5338 devices
are available that include a user-specified startup
frequency
Si5338C-Axxxxx-GM). See "12. Ordering Information"
on page 40 for details.
Figure 8. Si5338 Memory Configuration
configuration
2
2
C port. A single pin to enable/disable all
C interface. ClockBuilder Desktop (see
Default
Config
(OTP)
Power-Up/POR
NVM
(example
RAM
I
2
C
2
C interface. The
Si5338
part
number
2
19
C