K3HB-XAD 24VAC/VDC Omron, K3HB-XAD 24VAC/VDC Datasheet - Page 16
![PROCESS INDICATR DC CURRNT INPUT](/photos/29/87/298745/k3hb-x_sml.jpg)
K3HB-XAD 24VAC/VDC
Manufacturer Part Number
K3HB-XAD 24VAC/VDC
Description
PROCESS INDICATR DC CURRNT INPUT
Manufacturer
Omron
Series
K3HBr
Type
Process Meterr
Specifications of K3HB-XAD 24VAC/VDC
Measuring Range
0 ~ 199.99mA
Display Style
Green, Red Characters, Black Background
Display Type
LCD
Display Face Size
3.78" L x 1.89" W (96.0 x 48.0mm)
Display Digits
5
Display Digits - Height
0.193" (4.90mm), 0.559" (14.20mm)
Backlight
Green, Red
Mounting Type
Panel Mount
Termination
Screw Terminals
Voltage - Supply
24VAC/DC
Analog / Digital
Digital
Control Method
ON/OFF
Voltage Rating
24 V
Mounting
Panel
Size
95 mm L x 96 mm W x 44.8 mm H
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
K3HB-XAD24VAC/VDC
K3HBXAD24VACVDC
K3HBXAD24VACVDC
■ Safety Precautions
Do not touch the terminals while power is being supplied.
Doing so may possibly result in electric shock. Make sure
that the terminal cover is installed before using the
product.
Always provide protective circuits in the network. Without
protective circuits, malfunctions may possibly result in
accidents that cause serious injury or significant property
damage.
Provide double or triple safety measures in external
control circuits, such as emergency stop circuits, interlock
circuits, or limit circuits, to ensure safety in the system if
an abnormality occurs due to malfunction of the product
or another external factor affecting the product's
operation.
Do not allow pieces of metal, wire clippings, or fine
metallic shavings or filings from installation to enter the
product. Doing so may occasionally result in minor
electric shock, fire, or malfunction.
Do not use the product in locations where flammable or
explosive gases are present. Doing so may occasionally
result in explosion, causing minor or moderate injury, or
property damage.
Do not attempt to disassemble, repair, or modify the
product. Doing so may occasionally result in minor or
moderate injury due to electric shock.
Do not use the equipment for measurements within
Measurement Categories III and IV for K3HB-X and II, III,
and IV for K3HB-S, K3HB-V, and K3HB-H (according to
IEC61010-1). Doing so may occasionally cause
unexpected operation, resulting in minor or moderate
injury, or damage to the equipment. Use the equipment
for measurements only within the Measurement Category
for which the product is designed.
Perform correct setting of the product according to the
application. Failure to do so may occasionally cause
unexpected operation, resulting in minor or moderate
injury, or damage to the equipment.
Ensure safety in the event of product failure by taking
safety measures, such as installing a separate monitoring
system. Product failure may occasionally prevent
operation of comparative outputs, resulting in damage to
the connected facilities and equipment.
Tighten the screws on the terminal block and the
connector locking screws securely using a tightening
torque within the following ranges. Loose screws may
occasionally cause fire, resulting in minor or moderate
injury, or damage to the equipment.
Terminal block screws: 0.43 to 0.58 N·m
Connector locking screws: 0.18 to 0.22 N·m
Make sure that the product will not be adversely affected
if the DeviceNet cycle time is lengthened as a result of
changing the program with online editing. Extending the
cycle time may cause unexpected operation, occasionally
resulting in minor or moderate injury, or damage to the
equipment.
Before transferring programs to other nodes or changing
I/O memory of other nodes, check the nodes to confirm
safety. Changing the program or I/O memory of other
nodes may occasionally cause unexpected operation,
resulting in minor or moderate injury, or damage to the
equipment.
!WARNING
!CAUTION
Precautions for Safe Use
1. Do not use the product in the following locations.
• Locations subject to direct radiant heat from heating equipment
• Locations where the product may come into contact with water or
• Locations subject to direct sunlight
• Locations where dust or corrosive gases (in particular, sulfuric or
• Locations subject to extreme temperature changes
• Locations where icing or condensation may occur
• Locations subject to excessive shocks or vibration
2. Do not use the product in locations subject to temperatures or
3. Provide sufficient space around the product for heat dissipation.
4. Use and store the product within the specified temperature and
5. The service life of the output relays depends on the switching
6. Install the product horizontally.
7. Mount to a panel between 1 and 8-mm thick.
8. Use the specified size of crimp terminals (M3, width: 5.8 mm
9. In order to prevent inductive noise, wire the lines connected to the
10.Ensure that the rated voltage is achieved no longer than 2 s after
11.Allow the product to operate without load for at least 15 minutes
12.Do not install the product near devices generating strong high-fre-
13.Do not use thinner to clean the product. Use commercially avail-
14.Be sure to confirm the name and polarity for each terminal before
15.Use the product within the noted supply voltage and rated load.
16.Do not connect anything to unused terminals.
17.Output turns OFF when the mode is changed or settings are ini-
18.Install an external switch or circuit breaker that complies with
19.Use the specified cables for the communications lines and stay
20.Do not pull the DeviceNet communications cables with excessive
21.Do not connect or remove connectors while the DeviceNet power
22.Use cables with a heat resistance of 70ºC min.
oil
ammonia gas) are present
humidity levels outside the specified ranges or in locations prone
to condensation. If the product is installed in a panel, ensure that
the temperature around the product (not the temperature around
the panel) does not go outside the specified range.
humidity ranges. If several products are mounted side-by-side or
arranged in a vertical line, the heat dissipation will cause the inter-
nal temperature of the products to rise, shortening the service life.
If necessary, cool the products using a fan or other cooling
method.
capacity and switching conditions. Consider the actual application
conditions and use the product within the rated load and electrical
service life. Using the product beyond its service life may result in
contact welding or burning.
max.) for wiring. To connect bare wires, use AWG22 (cross sec-
tion: 0.326 mm
power supply terminals and AWG28 (cross section: 0.081 mm
to AWG16 (cross section: 1.309 mm
of exposed wire: 6 to 8 mm)
product separately from power lines carrying high voltages or cur-
rents. Do not wire in parallel with or in the same cable as power
lines. Other measures for reducing noise include running lines
along separate ducts and using shield lines.
turning the power ON.
after the power is turned ON.
quency waves or surges. When using a noise filter, check the volt-
age and current and install it as close to the product as possible.
able alcohol.
wiring the terminal block and connectors.
tialized. Take this into consideration when setting up the control
system.
applicable IEC60947-1 and IEC60947-3 requirements and label
them clearly so that the operator can quickly turn OFF the power.
within the specified DeviceNet communications distances. Refer
to the User's Manual (Cat. No. N129) for details on communica-
tions distance specifications and cables.
force or bend them past their natural bending radius.
is being supplied. Doing so will cause product failure or malfunc-
tion.
2
) to AWG14 (cross section: 2.081 mm
2
) for other terminals. (Length
K3HB-X
2
) to wire the
2
)
16