E5GN-Q1TD AC/DC24 Omron, E5GN-Q1TD AC/DC24 Datasheet - Page 16

• Manufacturer Part Number: E5GN-Q1TD AC/DC24
• Description: CONTROL TEMP DGTL VOLT OUT 24V
• Manufacturer: Omron
• Type: Digital Temperature Controllerr

Specifications of E5GN-Q1TD AC/DC24

• Analog / Digital: Digital
• Control Method: ON/OFF
• Voltage Rating: 24 VAC, 24 VDC
• Mounting: Panel
• Display Type: 11-Segment, 4 Digit
• Size: 99 mm x 48 mm x 35 mm
• Features: Compatible with Support Software (CX-Thermo version 4.2 or higher)
• Input Type: Thermocouple
• Output Type: Voltage
• Operating Temperature Max: 55°C
• Operating Temperature Min: -10°C
• Temperature Accuracy ±: 0.2%
• Output Voltage Max: 13.8VDC
• Output Voltage Min: 10.2VDC
• Meter Function: Thermocouple
• Thermocouple Type: J, K, T, E, L, U, N, R, S, B, W, PLII
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: E5GNQ1TDACDC24; Z3048

Safety Precautions
16
Do not touch the terminals while power is being supplied.
Doing so may occasionally result in minor injury due to
electric shock.
Do not allow pieces of metal, wire clippings, or fine
metallic shavings or filings from installation to enter the
product. Doing so may occasionally result in electric
shock, fire, or malfunction.
Do not use the product where subject to flammable or
explosive gas. Otherwise, minor injury from explosion
may occasionally occur.
Do not leave the conversion cable connected to the
product. Malfunction may occur due to noise in the cable.
Do not use the Temperature Controller or Conversion
Cable if it is damaged. Doing so may occasionally result
in minor electric shock or fire.
Never disassemble, modify, or repair the product or touch
any of the internal parts. Minor electric shock, fire, or
malfunction may occasionally occur.
CAUTION - Risk of Fire and Electric Shock
a) This product is UL listed as Open Type Process
b) More than one disconnect switch may be required to
c) Signal inputs are SELV, limited energy. (See note 1.)
d) Caution: To reduce the risk of fire or electric shock, do
If the output relays are used past their life expectancy,
contact fusing or burning may occasionally occur.
Always consider the application conditions and use the
output relays within their rated load and electrical life
expectancy. The life expectancy of output relays varies
considerably with the output load and switching
conditions.
Tighten the terminal screws properly. Tighten them to a
torque of 0.24 N·m (2.5 kgf·cm) max. on terminals 1 to 6.
Tighten them to a torque of 0.13 N·m (1.4 kgf·cm) max.
on terminals 7 to 9. Loose screws may cause
malfunction.
Set the parameters of the product so that they are
suitable for the system being controlled. If they are not
suitable, unexpected operation may occasionally result in
property damage or accidents.
A malfunction in the product may occasionally make
control operations impossible or prevent alarm outputs,
resulting in property damage. To maintain safety in the
event of malfunction of the product, take appropriate
safety measures, such as installing a monitoring device
on a separate line.
Control Equipment. It must be mounted in an
enclosure that does not allow fire to escape externally.
de-energize the equipment before servicing the
product.
not interconnect the outputs of different Class 2
circuits. (See note 2.)
Digital Temperature Controllers
!CAUTION
E5GN
Note: 1. An SELV circuit is one separated from the power supply with
A semiconductor is used in the output section of long-life
relays. If excessive noise or surge is impressed on the
output terminals, a short-circuit failure is likely to occur. If
the output remains shorted, fire will occur due to
overheating of the heater or other cause. Take measures
in the overall system to prevent excessive temperature
increase and to prevent fire from spreading.
Do not allow pieces of metal or wire cuttings to get inside
connectors. Failure to do so may occasionally result in
minor electric shock, fire, or damage to equipment.
2. A class 2 power supply is one tested and certified by UL as
double insulation or reinforced insulation, that does not
exceed 30 V r.m.s. and 42.4 V peak or 60 VDC.
have the current and voltage of the secondary output
restricted to specific levels.