CAT5401WI-00-TE13 ON Semiconductor, CAT5401WI-00-TE13 Datasheet - Page 4

• Manufacturer Part Number: CAT5401WI-00-TE13
• Manufacturer: ON Semiconductor

Specifications of CAT5401WI-00-TE13

• Number Of Elements: 4
• # Of Taps: 64
• Resistance (max): 100KOhm
• Power Supply Requirement: Single
• Interface Type: Serial (SPI)
• Single Supply Voltage (typ): 3.3/5V
• Dual Supply Voltage (typ): Not RequiredV
• Single Supply Voltage (min): 2.5V
• Single Supply Voltage (max): 6V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 24
• Lead Free Status / RoHS Status: Compliant

ABSOLUTE MAXIMUM RATINGS*
Temperature Under Bias .................. -55°C to +125°C
Storage Temperature ........................ -65°C to +150°C
Voltage on any Pin with
V
Package Power Dissipation
Lead Soldering Temperature (10 secs) ............ 300°C
Wiper Current .................................................. +12mA
Notes:
(1) This parameter is tested initially and after a design or process change that affects the parameter.
(2) Absolute linearity is utilitzed to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a potentiometer.
(3) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a
(4) LSB = R
(5) n = 0, 1, 2, ..., 63
Document No. 2010, Rev. F
POTENTIOMETER CHARACTERISTICS
Over recommended operating conditions unless otherwise stated.
Notes:
(1) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC voltage on output
(2) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1V to V
C
CC
TC
Symbol
TC
H
V
R
R
R
R
potentiometer. It is a measure of the error in step size.
Respect to V
Capability (T
pins is V
/C
R
R
TERM
V
with Respect to Ground ................ -2.0V to +7.0V
I
RATIO
POT
POT
POT
POT
RPOT
fc
W
W
W
N
L
/C
W
TOT
CC
+0.5V, which may overshoot to V
Potentiometer Resistance Tolerance
/ 63 or (R
Temperature Coefficient of R
Potentiometer Resistance (-2.5)
Potentiometer Resistance (-00)
Potentiometer Resistance (-50)
Potentiometer Resistance (-10)
Ratiometric Temp. Coefficient
Voltage on any R
Potentiometer Capacitances
A
SS
= 25°C) ................................... 1.0W
(1)
H
Frequency Response
Absolute Linearity
Relative Linearity
- R
Wiper Resistance
Wiper Resistance
................... -2.0V to +V
R
L
Wiper Current
Power Rating
) / 63, single pot
POT
Parameter
Resolution
Noise
Matching
H
or R
CC
(3)
(2)
L
+2.0V for periods of less than 20 ns.
Pin
POT
CC
+2.0V
R
I
I
W
w(n)(actual)
W
R
= +3mA @ V
= +3mA @ V
Test Conditions
w(n+1)
25°C, each pot
R
POT
V
4
-[R
SS
-R
(1)
(1)
(1)
(1)
(1)
= 50kΩ
*COMMENT
Stresses above those listed under “Absolute Maximum Ratings” may cause permanent
damage to the device. These are stress ratings only, and functional operation of the
device at these or any other conditions outside of those listed in the operational sections
of this specification is not implied. Exposure to any absolute maximum rating for extended
periods may affect device performance and reliability.
= 0V
w(n)+LSB
(n)(expected)
CC
CC
Recommended Operating Conditions:
V
Temperature
Industrial
= 5V
=3V
]
CC
(5)
(5)
= +2.5V to +6.0V
CC
+1V.
GND
Min
10/10/25
Characteristics subject to change without notice
+300
TBD
Typ
100
2.5
1.6
0.4
-40°C
50
10
80
Min
© Catalyst Semiconductor, Inc.
Max
+0.2
V
+20
300
150
50
+6
+1
20
1
CC
Max
85°C
ppm/°C
ppm/°C
nV/ Hz
LSB
LSB
Units
MHz
mW
mA
kΩ
kΩ
kΩ
kΩ
pF
%
%
%
Ω
Ω
V
(4)
(4)