LFXP2-30E-6FTN256I LATTICE SEMICONDUCTOR, LFXP2-30E-6FTN256I Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/3/381/lattice_semiconductor_sml.jpg)
LFXP2-30E-6FTN256I
Manufacturer Part Number
LFXP2-30E-6FTN256I
Description
FPGA LatticeXP2 Family 29000 Cells Flash Technology 1.2V 256-Pin FTBGA
Manufacturer
LATTICE SEMICONDUCTOR
Datasheet
1.LFXP2-40E-5FN484I.pdf
(92 pages)
Specifications of LFXP2-30E-6FTN256I
Package
256FTBGA
Family Name
LatticeXP2
Device Logic Units
29000
Typical Operating Supply Voltage
1.2 V
Maximum Number Of User I/os
201
Ram Bits
396288
Re-programmability Support
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LFXP2-30E-6FTN256I
Manufacturer:
Lattice Semiconductor Corporation
Quantity:
10 000
Lattice Semiconductor
Figure 2-4. General Purpose PLL (GPLL) Diagram
Table 2-4 provides a description of the signals in the GPLL blocks.
Table 2-4. GPLL Block Signal Descriptions
Clock Dividers
LatticeXP2 devices have two clock dividers, one on the left side and one on the right side of the device. These are
intended to generate a slower-speed system clock from a high-speed edge clock. The block operates in a ÷2, ÷4 or
÷8 mode and maintains a known phase relationship between the divided down clock and the high-speed clock
based on the release of its reset signal. The clock dividers can be fed from the CLKOP output from the GPLLs or
from the Edge Clocks (ECLK). The clock divider outputs serve as primary clock sources and feed into the clock dis-
tribution network. The Reset (RST) control signal resets the input and forces all outputs to low. The RELEASE sig-
nal releases outputs to the input clock. For further information on clock dividers, please see TN1126,
sysCLOCK PLL Design and Usage
CLKI
CLKFB
RST
RSTK
DPHASE [3:0]
DDDUTY [3:0]
WRDEL
CLKOS
CLKOP
CLKOK
CLKOK2
LOCK
DPHASE
WRDEL
DDUTY
CLKFB
RSTK
Signal
CLKI
RST
I/O
O
O
O
O
O
I
I
I
I
I
I
I
Clock input from external pin or routing
DPA Phase Adjust input
DPA Duty Cycle Select input
PLL feedback input from CLKOP (PLL internal), from clock net (CLKOP) or from a user clock
(PIN or logic)
“1” to reset PLL counters, VCO, charge pumps and M-dividers
“1” to reset K-divider
DPA Fine Delay Adjust input
PLL output clock to clock tree (phase shifted/duty cycle changed)
PLL output clock to clock tree (no phase shift)
PLL output to clock tree through secondary clock divider
PLL output to clock tree (CLKOP divided by 3)
“1” indicates PLL LOCK to CLKI
CLKFB
Divider
Divider
CLKI
Guide. Figure 2-5 shows the clock divider connections.
Internal Feedback
PFD
LOOP FILTER
2-7
VCO/
Description
CLKOP
Divider
Detect
Lock
LatticeXP2 Family Data Sheet
Duty Cycle/
Duty Trim
Duty Trim
CLKOK
Phase/
Divider
3
Architecture
LatticeXP2
CLKOK2
CLKOS
CLKOP
CLKOK
LOCK