BTS5210G-L Infineon Technologies, BTS5210G-L Datasheet
BTS5210G-L
Specifications of BTS5210G-L
Related parts for BTS5210G-L
BTS5210G-L Summary of contents
Page 1
...
Page 2
... AEC Qualified • Green product (RoHS compliant) Data Sheet Smart High-Side Power Switch Ω Ω Ω ® Block Diagram 2 BTS5210G Package P-DSO-14 PG-DSO-14-37 Rev. 1.3, 2009-04-16 ...
Page 3
... Data Sheet control and protection circuit equivalent to channel 1 3 Smart High-Side Power Switch BTS5210G Rev. 1.3, 2009-04-16 ...
Page 4
... OUT2 11 NC Not Connected Data Sheet Smart High-Side Power Switch Pin configuration (top view GND 2 IN1 3 ST1 4 IN2 5 ST2 BTS5210G • OUT1 12 OUT1 OUT2 9 OUT2 Rev. 1.3, 2009-04-16 ...
Page 5
... IN: ST require an external current limit for the GND and status pins (a 150Ω bb(AZ) 2 (one layer, 70μm thick) copper area for Smart High-Side Power Switch BTS5210G Symbol Values self-limited Load dump T -40 ...
Page 6
... I L(NOM L(GNDhigh 90 OUT 10 OUT off = 12 Ω / OUT Ω / OUT L 2 (one layer, 70μm thick) copper area for Smart High-Side Power Switch BTS5210G Values min typ max -- -- Values min typ max -- 110 140 -- 210 280 -- 55 70 1.8 2.4 -- 3.4 3 ...
Page 7
... T require an external current limit for the GND and status pins (a 150Ω bb(AZ) ON(CL) 7 Smart High-Side Power Switch Values min typ max 0.5 0.9 -- 1.0 1 6 150 -- -- table of protection functions and Rev. 1.3, 2009-04-16 BTS5210G Unit 11 μ 11) μ ° ...
Page 8
... IN(off IN(on +1.6 mA +1.6 mA Smart High-Side Power Switch Values min typ -- -- bb -- 600 ON 1.7 2.8 OUT(OL) 1 2.5 4 IN(T+) 1.0 -- IN(T-) -- 0.2 IN( 5.4 -- ST(high ST(low) Rev. 1.3, 2009-04-16 BTS5210G Unit max 4.0 V 6.0 kΩ 2 —s 20 —s -- —s 500 —s 20 μA 20 μ 0.6 ...
Page 9
... R GND operating voltage potential at the Output exceeds the OpenLoad detection voltage 20 Data Sheet IN OUT high impedance, potential depends on external circuit = 150 Ω for reverse battery protection up to the max. GND 9 Smart High-Side Power Switch BTS5210G Rev. 1.3, 2009-04-16 ...
Page 10
... Open-load detection, OFF-state diagnostic condition: Open Load OUT < 375 Ω ST(ON) GND disconnect Any kind of load. In case high is V Due to V > GND 10 Smart High-Side Power Switch BTS5210G = 150 Ω typ., R GND Z2 OUT1 or OUT2 > typ.; IN low ≈ OUT IN IN(T+) = low signal available. ...
Page 11
... Energy stored in load inductance: While demagnetizing load inductance, the energy dissipated in PROFET with an approximate solution for R L > 0 Ω: · · Maximum allowable load inductance for a single switch off / j,start = 150° Ω [mH Smart High-Side Power Switch BTS5210G ^ · · · i (t) dt ...
Page 12
... Typ. on-state resistance high L R [mOhm] ON Typ. standby current , I 9...34 V, IN1,2 = low EE RII [μA] bb(off) Data Sheet Smart High-Side Power Switch V [ [° BTS5210G Rev. 1.3, 2009-04-16 ...
Page 13
... Data Sheet Figure 2b: Switching a lamp: Figure 3a: Turn on into short circuit: shut down by overtemperature, restart by cooling off Heating up of the chip may require several milliseconds, depending on external conditions 13 Smart High-Side Power Switch BTS5210G Rev. 1.3, 2009-04-16 ...
Page 14
... Reset if T < Data Sheet Smart High-Side Power Switch Figure 5a: Open load: detection in OFF-state, turn on/off to open load Open load of channel 1; other channels normal operation Figure 6a: Status change after, turn on/off to overtemperature Overtemperature of channel 1; other channels normal operation 14 BTS5210G Rev. 1.3, 2009-04-16 ...
Page 15
... A B 14x 8.75 -0.2 A Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Lead width can be 0.61 max. in dambar area 15 Smart High-Side Power Switch 0.35 x 45˚ 0.64 ±0.25 6 ±0.2 0 GPS01230 Dimensions in mm Rev. 1.3, 2009-04-16 BTS5210G ...
Page 16
... Creation of the green datasheet. First page : Adding the green logo and the AEC qualified Adding the bullet AEC qualified and the RoHS compliant features Package page Modification of the package to be green. Data Sheet Smart High-Side Power Switch 16 BTS5210G Rev. 1.3, 2009-04-16 ...
Page 17
... Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life ...