BTM7710GPXT Infineon Technologies, BTM7710GPXT Datasheet
BTM7710GPXT
Specifications of BTM7710GPXT
Related parts for BTM7710GPXT
BTM7710GPXT Summary of contents
Page 1
...
Page 2
Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 3
... The BTM7710GP is part of the TrilithIC family containing three dies in one package: One double high-side switch and two low-side switches. The drains of these three vertical DMOS chips are mounted on separated lead frames. The sources are connected to individual pins, so the BTM7710GP can be used in H-bridge- as well as in any other configuration ...
Page 4
Pin Configuration 2.1 Pin Assignment IL1 SL1 SH1 5 GND 6 IH1 7 DHVS IH2 10 SH2 IL2 SL2 15 Figure 1 Pin Assignment ...
Page 5
... Not connected 5 SH1 Source of high-side switch 1 6 GND Ground of high-side switches 7 IH1 Digital input of high-side switch 1 8 DHVS Drain of high-side switches and power supply voltage 9 ST Status; open Drain output 10 IH2 Digital input of high-side switch 2 11 SH2 Source of high-side switch Not connected ...
Page 6
Terms IH1 IH1 V STL V STZ I IH1 IH2 V IH1 GND V IH2 I GND I LKCL I IL1 IL1 I V IL2 IL2 IL1 ...
Page 7
Block Diagram IH1 10 IH2 6 GND 1 IL1 13 IL2 Figure 3 Block Diagram BTM7710GP Datasheet DHVS Diagnosis Biasing and Protection Driver IN OUT ...
Page 8
... Output Stages The output stages consist of an low diodes can be used for freewheeling when communicating inductive loads. If the high-side switches are used as single switches, positive and negative voltage spikes which occur when driving inductive loads are limited by integrated power clamp diodes. ...
Page 9
... Table 3 Truth table and Diagnosis (valid only for the High-Side-Switches) Flag Normal operation; identical with functional truth table Overtemperature high-side switch1 Overtemperature high-side switch2 Overtemperature both high-side switches Under voltage Inputs Logic LOW 1 = Logic HIGH X = don’t care Datasheet IH1 IH2 ...
Page 10
... Electrical Characteristics 5.1 Absolute Maximum Ratings 1) Absolute Maximum Ratings – 40 °C < T < 110 °C j Pos. Parameter High-Side-Switches (Pins DHVS, IH1,2 and SH1,2) 5.1.1 Supply voltage 5.1.2 Supply voltage for full short circuit protection 5.1.3 HS-drain current 5.1.4 HS-input current 5.1.5 HS-input voltage Status Output ST 5 ...
Page 11
... Pos. Parameter Current Consumption HS-switch 5.4.4 Quiescent current 5.4.5 Supply current; one HS-switch active 5.4.6 Supply current; both HS-switches active 5.4.7 Leakage current of high-side switch 5.4.8 Leakage current through logic GND in free wheeling condition Datasheet Symbol Limit Values min. V ...
Page 12
... Under Voltage Lockout HS-switch 5.4.11 Switch-ON voltage 5.4.12 Switch-OFF voltage 5.4.13 Switch ON/OFF hysteresis Output stages 5.4.14 Inverse diode of high-side switch; Forward-voltage 5.4.15 Inverse diode of low-side switch; Forward-voltage 5.4.16 Static drain-source on-resistance of high-side switch 5.4.17 Static drain-source on-resistance of low-side switch Datasheet < 110 ° < V < ...
Page 13
... A; – 40 °C < SH1 SH2 SL1 SL2 unless otherwise specified Pos. Parameter Short Circuit of high-side switch to GND 5.4.18 Initial peak SC current 100 µ del S Short Circuit of high-side switch to 5.4.19 Output pull-down-resistor 1) Thermal Shutdown 5.4.20 Thermal shutdown junction temperature 5.4.21 Thermal switch-on junction temperature 5 ...
Page 14
... A; – 40 °C < SH1 SH2 SL1 SL2 unless otherwise specified Pos. Parameter Control Inputs of high-side switches 5.4.38 H-input voltage 5.4.39 L-input voltage 5.4.40 Input voltage hysteresis 5.4.41 H-input current 5.4.42 L-input current 5.4.43 Input series resistance 5.4.44 Zener limit voltage Control Inputs IL1 ...
Page 15
Application Information Note: The following simplified application examples are given as a hint for the implementation of the device only and shall not be regarded as a description or warranty of a certain functionality, condition or quality of the ...
Page 16
Package Outlines 1 ±0.2 5.56 4.8 1) Typical All metal surfaces tin plated, except area of cut. Footprint Figure 5 PG-TO263-15-1 (Plastic Transistor Single Outline Package) Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly ...
Page 17
Revision History Rev. Date Changes Initial version 1.0 2008-07-07 Datasheet 17 BTM7710GP Rev. 1.0, 2008-07-07 ...
Page 18
... Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life ...