SDINB11024 SanDisk, SDINB11024 Datasheet
SDINB11024
Specifications of SDINB11024
Related parts for SDINB11024
SDINB11024 Summary of contents
Page 1
... SanDisk Product Manual Version 3.1 Document No. 80-36-00450 December 2006 SanDisk Corporation Corporate Headquarters • 601 McCarthy Boulevard • Milpitas, CA 95035 Phone (408) 801-1000 • Fax (408) 801-8657 www.sandisk.com ...
Page 2
... Corporation general policy does not recommend the use of its products in life support applications where in a failure or malfunction of the product may directly threaten life or injury. Per SanDisk Terms and Conditions of Sale, the user of SanDisk products in life support applications assumes all risk of such use and indemnifies SanDisk against all damages. See “Disclaimer of Liability.” ...
Page 3
... General ...................................................................................................4-1 4.2 SD Bus Protocol .....................................................................................4-1 4.3 Functional Description............................................................................4-1 Appendix A Capacitor Specifications ..........................................................A-1 Appendix B Ordering Information .............................................................. B-1 Appendix C SanDisk Worldwide Sales Offices........................................... C-1 Appendix D Limited Warranty ....................................................................D-1 Appendix E Disclaimer of Liability............................................................. E-1 © 2006 SanDisk Corporation SanDisk iNAND Product Manual ...
Page 4
... In addition to the mass-storage-specific flash memory chip, iNAND includes an intelligent controller, which manages interface protocols, data storage and retrieval, error correction code (ECC) algorithms, defect handling and diagnostics, power management, wear leveling, and clock control. Figure 1 block diagram of the SanDisk iNAND with SD Interface. Figure 1-1 ...
Page 5
... Document Scope This document describes the key features and specifications of the SanDisk iNAND as well as the information required to interface host system. Chapter 2 describes the physical and mechanical properties of iNAND, Chapter 3 contains the pins and register overview, and Chapter 4 gives a general overview of the SD protocol ...
Page 6
... Power management for low power operation 1.6 Technology Independence The 512-byte sector size of the SanDisk iNAND is the same as that in an IDE magnetic disk drive. To write or read a sector (or multiple sectors), the host software simply issues a read or write command to the card. The command contains the address and number of sectors to write or read ...
Page 7
... SD Bus Mode The following sections provide valuable information on SanDisk iNAND in SD Bus mode. SanDisk iNAND devices are fully compliant with the SDA Physical Layer Specification, Version 2.00. Card Specific Data (CSD) Register structures are compliant with CSD Structure 1 ...
Page 8
... Start Address (Write) Multiple Block Mode Memory Memory Memory Memory Sectors Sectors Sectors Sectors Write Start Address Stop Start 1-5 Chapter 1 – Introduction SanDisk iNAND Product Manual Block Block Block Misalignment Error Memory Memory Sectors Sectors Start Address (Read/Write) Memory Memory Sectors ...
Page 9
... Motorola and other vendors’ microcontrollers. Table 1-1 contains names and descriptions of SPI Mode functions. More information about SPI Mode can be found in Section 7 or the SDA Physical Layer Specification, Version 2.00. © 2006 SanDisk Corporation Chapter 1 – Introduction SanDisk iNAND Product Manual Description 1-6 12/07/06 ...
Page 10
... Block Write Access Time CMD1 to Ready after Power-up 2.4 System Reliability and Maintenance Table 2-3 Reliability and Maintenance Specifications MTBF Preventative Maintenance Data Reliability © 2006 SanDisk Corporation Chapter 2 – Product Specifications SanDisk iNAND Product Manual Value Measurement 250 uA 100 mA 100 mA Maximum Value 100 ms ...
Page 11
... Revision 3.1 2.5 Physical Specifications The SanDisk iNAND is a 56-pin, thin fine-pitched ball grid array (BGA). See Figure 2-1 (56-pin) for physical specifications and dimensions. See Figure 2-2 for a top view of the pin definitions. Figure 2-1 iNAND Specifications (18 x 12mm Package) Top View © ...
Page 12
... VDD VDD VDD GND VDD 2-3 Chapter 2 – Product Specifications SanDisk iNAND Product Manual Dimension in inches Nominal Maximum --- 0.047 0.014 0.015 0.029 0.031 0.709 0.713 0.472 0.476 0.276 --- 0.433 --- 0.512 --- 0.276 --- 0.039 --- 0.020 0.022 0.004 0.004 0.006 0.010 0.004 12/11 H2 GND ...
Page 13
... SDINB1-4096 * 1 megabyte (MB million bytes; 1 gigabyte (GB billion bytes. Some of the listed capacity is used for formatting and other functions, and thus is not available for data storage. © 2006 SanDisk Corporation Chapter 2 – Product Specifications SanDisk iNAND Product Manual Capacity 256 MB 512 MB 1024 MB 2048 MB ...
Page 14
... Revision 3.1 3 iNAND Interface Description 3.1 Pins and Registers Table 3-1 contains the SanDisk iNAND functional ball assignment Table 3-1 iNAND Pin Assignment Pin No. Name SD Bus Mode H6, F1, C1, VDD A2, A6 H7, H2, D1, VSS B1 DAT0 G3 DAT1 G6 DAT2 G5 DAT3 G1 CLK G4 CMD B5 WPB G7 RSTB B2 RDY/BSY ...
Page 15
... WPB G7 RSTB B2 RDY/BSY B3 SEL_A B4 SEL_B G8 FCAP SanDisk iNAND contains a set of information registers. Register descriptions and SDA references are provided in Section 5.0 of the SDA Physical Layer Specification, Version 2.00. Table 3-2 iNAND Register Overview Register Abbreviation CID RCA CSD SCR OCR SSR CSR 3 ...
Page 16
... Revision 3.1 3.3 Electrical Interface The power scheme of SanDisk iNAND is handled locally in each card and in the bus master. Refer to Section 6.4 of the SDA Physical Layer Specification, Version 2.00. 3.3.1 Power Up Refer to Section 6.4.1 of the SDA Physical Layer Specification, Version 2.00. 3.3.2 Bus Operating Conditions SPI Mode bus operating conditions are identical to SD Bus Mode operating conditions ...
Page 17
... Reserved Manufacture Date Code (MDT) CRC7 checksum (CRC) Not used, always Note: SD-3C, LLC is a limited liability company established by Matsushita Electric Industrial Co. Ltd., SanDisk Corporation and Toshiba Corporation. *The CRC checksum is computed by using the following formula: CRC Calculation: G( M(x)=(MID-MSB)*x CRC[6… ...
Page 18
... Partial blocks for read allowed No Write block misalignment No Read block misalignment No DSR implemented --- Reserved 2 GB Device size 1 GB 512 MB 256 MB 100 mA Max. read current @VDD min Max. read current @VDD max. 3-5 SanDisk iNAND Product Manual Version 1.01 to 1.10 --- Description 12/07/06 ...
Page 19
... COPY PERM_ WRITE_ PROTECT TMP_WRITE_PROTECT FILE_ FORMAT Reserved CRC --- © 2006 SanDisk Corporation Chapter 3 – iNAND Interface Description SanDisk iNAND Product Manual CSD Value Description 100 mA Max. write current @VDD min Max. write current @VDD max. 2G=2048 Device size multiplier 1G=1024 ...
Page 20
... R2W_ FACTOR WRITE_BL_ LEN WRITE_BL PARTIAL --- FILE_ FORMAT_ GRP COPY PERM_ WRITE_ PROTECT © 2006 SanDisk Corporation Chapter 3 – iNAND Interface Description SanDisk iNAND Product Manual CSD Value Description 2.0 CSD structure --- Reserved 1.5 ms Data read access time-1 0 Data read access time-2 in CLK cycles ...
Page 21
... Specification, Version 2.00 for more information. 3.4.7 SD Card Configuration Register The SD Card Configuration Register (SCR addition to the CSD Register. The SCR provides information about special features in SanDisk iNAND. For more information, refer to Section 5.6 in the SDA Physical Layer Specification, Version 2.00. 3.4.8 SD Card Registers in SPI Mode All registers are accessible in SPI Mode ...
Page 22
... Chapter 3 – iNAND Interface Description Number of Total Partition Partition Sectors System Area Sectors 8192 8,018,944 523 4,011,595 523 2,005,675 279 1,002,727 157 501,149 3-9 SanDisk iNAND Product Manual User Data User Data Sectors Bytes 8,012,708 4,102,506,496 4,011,072 2,053,668,864 2,005,152 1,026,637,824 1,002,448 513,253,376 500,992 256,507,904 12/07/06 ...
Page 23
... The host can use the bus clock signal in iNAND to switch them to energy saving mode or to control data flow on the bus. See Section 4.4 of the SDA Physical Layer Specification, Version 2.00. © 2006 SanDisk Corporation Chapter 4 – iNAND Protocol Description SanDisk iNAND Product Manual All iNAND commands, together with frequency range. This PP 4-1 ...
Page 24
... For more information, refer to Section 4.13 of the SDA Physical Layer Specification, Version 2.00. 4.3.10 Erase Timeout Calculation See Section 4.14 of the SDA Physical Layer Specification, Version 2.00. © 2006 SanDisk Corporation Chapter 4 – iNAND Protocol Description SanDisk iNAND Product Manual 4-2 12/07/06 ...
Page 25
... FCAP F1 VDD A6 VDD C1=C3>=2.2uF C3 C2=C4<=100nF C3, C4: X7R or XR5 VSS Close to ball A6 VSS Bottom View A-1 Appendix A –Capacitor Specifications SanDisk iNAND Product Manual Trace Requirements: Resistance < 2 ohm Inductance < VSS Capacitor Requirements: Capacitance > =2.2uF Voltage > =6.3V Dielectric X7R or XR5 C4 12/07/06 ...
Page 26
... Revision 3.1 Appendix B Ordering Information B.1 iNAND To order SanDisk products directly from SanDisk, call (408) 801-1000. Part Number SDINB1-256 SDINB1-512 SDINB1-1024 SDINB1-2048 SDINB1-4096 1 1 megabyte (MB million bytes; 1 gigabyte (GB billion bytes. Some of the listed capacity is used for formatting and other functions, and thus is not available for data storage. ...
Page 27
... Revision 3.1 Appendix C SanDisk Worldwide Sales Offices To order SanDisk products directly from SanDisk, call (408) 801-1000. SanDisk Corporate Headquarters 601 McCarthy Blvd. Milpitas, CA 95035 Tel: 408-801-1000 Fax: 408-801-8657 http://www.sandisk.com U.S. OEM Sales Offices Southwest/Northwest USA & Mexico 601 McCarthy Blvd. ...
Page 28
... III. WHAT THIS WARRANTY COVERS For products found to be defective within one year of purchase, SanDisk will have the option of repairing or replacing the defective product, if the following conditions are met warranty registration card for each defective product was submitted and is on file at SanDisk. If not, a warranty registration card must accompany each returned defective product. This card is included in each product’ ...
Page 29
... SanDisk reserves the right to repair or replace, at its discretion, any product returned by its customers, even if such product is not covered under warranty, but is under no obligation to do so. SanDisk may, at its discretion, ship repaired or rebuilt products identified in the same way as new products, provided such cards meet or exceed the same published specifications as new products. ...
Page 30
... SanDisk shall not be liable for any loss, injury or damage caused by use of the Products in any of the following applications: − ...