SMC128CFB6E Micron Technology Inc, SMC128CFB6E Datasheet

Page 1

Features Custom-designed, highly-integrated memory controller – Fully compliant with CompactFlash specification 3.0 – Fully compatible with PCMCIA specification 2.1 – PC Card ATA interface supported – True IDE mode compatible – PIO mode 6 supported – ...

Page 2

Contents Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 3

SMC128CF, SMC01GCF, SMC08GCF List of tables Table 1. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 4

List of figures List of figures Figure 1. CompactFlash memory card block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 5

... PCMCIA memory mode (personal computer memory card international association standard, JEIDA in Japan), and to the ATA specification when operating in true IDE mode. CompactFlash cards can be used with passive adapters in a PC-card type II or type III socket. The card has an internal intelligent controller which manages interface protocols, data storage and retrieval as well as hardware RS-code error correction code (ECC), defect handling, diagnostics and clock control ...

Page 6

... File size = 20 Mbytes sequential; sector count = 256. Table 3. Current consumption Current consumption (typ) Read Write Standby Sleep mode 1. All values are typical at 25 °C and nominal supply voltage and refer to 1-Gbyte CompactFlash card, operating in PIO mode. Table 4. Environmental specifications Environmental specifications Temperature Humidity (non-condensing) Salt water spray ...

Page 7

SMC128CF, SMC01GCF, SMC08GCF 2 Capacity specification Table 6 shows the specific capacity for the various CF models and the default number of heads, sector/tracks and cylinders. Table 6. CF capacity specification Root part Capacity Default_cylinders number SMC128CF 128 Mbytes SMC01GCF ...

Page 8

Card physical 3 Card physical 3.1 Physical description The CompactFlash memory card contains a single chip controller and flash memory module(s). The controller interfaces with a host system allowing data to be written to and read from the flash memory ...

Page 9

SMC128CF, SMC01GCF, SMC08GCF 4 Electrical interface 4.1 Electrical description The CompactFlash memory card operates in three basic modes: PC card ATA using I/O mode PC card ATA using memory mode True IDE mode, which is compatible with most disk drives. ...

Page 10

Electrical interface Table 7. Pin assignment and pin type (continued) PC card memory mode Pin Signal Pin num name type 17 A03 I 18 A02 I 19 A01 I 20 A00 I 21 D00 I/O 22 D01 I/O 23 D02 ...

Page 11

SMC128CF, SMC01GCF, SMC08GCF Table 7. Pin assignment and pin type (continued) PC card memory mode Pin Signal Pin num name type 46 BVD1 I/O I1U,OT1 (3) 47 D08 I/O (3) 48 D09 I/O (3) 49 D10 I/O 50 GND 1. ...

Page 12

Electrical interface Table 8. Signals description (continued) Signal name Dir. D15-D00 (PC card memory mode) D15-D00 I/O (PC card I/O mode) D15-D00 (True IDE mode) GND (PC card memory mode) GND (PC card I/O mode) GND (True IDE mode) –INPACK ...

Page 13

SMC128CF, SMC01GCF, SMC08GCF Table 8. Signals description (continued) Signal name Dir. –IORD (PC card memory mode) –IORD (PC card I/O mode) –IORD (True IDE mode - except Ultra DMA Protocol Active) –HDMARDY (True IDE mode - in Ultra DMA Protocol ...

Page 14

Electrical interface Table 8. Signals description (continued) Signal name Dir. –IOWR (PC card memory mode) –IOWR (PC card I/O mode) –IOWR (True IDE mode - except Ultra DMA Protocol Active) –STOP (True IDE mode - Ultra DMA Protocol Active) –OE ...

Page 15

SMC128CF, SMC01GCF, SMC08GCF Table 8. Signals description (continued) Signal name Dir. RESET (PC card memory mode) RESET (PC card I/O mode) –RESET (True IDE mode (PC card memory mode (PC card I/O mode (True ...

Page 16

Electrical interface Table 8. Signals description (continued) Signal name Dir. –WE (PC card memory mode) –WE (PC card I/O mode) –WE (True IDE mode) WP (PC card memory mode) –IOIS16 O (PC card I/O mode) –IOCS16 (True IDE mode) 16/29 ...

Page 17

SMC128CF, SMC01GCF, SMC08GCF 4.2 Electrical specification Table 9 defines the DC characteristics for the CompactFlash memory card. Unless otherwise stated, conditions are ± 10 3.3 V ± 10% CC -40 ° ...

Page 18

... When operating in a CompactFlash advanced timing mode, the following conditions must be respected: Only one CompactFlash card must be connected to the CompactFlash bus The load capacitance (cable included) for all signals must be lower than 40 pF The cable length must be lower than 0. inches). The cable length is measured from the card connector to the host controller ...

Page 19

SMC128CF, SMC01GCF, SMC08GCF 5 Command interface There are two types of bus cycles and timing sequences that occur in the PCMCIA type interface, direct mapped I/O transfer and memory access. Three types of bus cycles are also available in true ...

Page 20

... The load presented to the host by cards supporting Ultra DMA is more controlled than that presented by other CompactFlash cards. Therefore, the use of a card that does not support Ultra DMA in a master/slave arrangement with a Ultra DMA card can affect the critical timing of the Ultra DMA transfers ...

Page 21

SMC128CF, SMC01GCF, SMC08GCF 11 CIS information (typical) -------- 0000: Code 01, link -------- – Tuple CISTPL_DEVICE (01), length 4 (04) – Device type is FUNCSPEC – Extended speed byte used – Device speed is 80ns ...

Page 22

CIS information (typical) -------- – Tuple CISTPL_VERS_1 (15), length 18 (12) – Major version 4, minor version 1 – Product Information: Manufacturer: ‘Numonyx’, – Product name: ‘Numonyx-xxxxB’ -------- 0056: Code 21, link -------- – Tuple CISTPL_FUNCID (21), ...

Page 23

SMC128CF, SMC01GCF, SMC08GCF -------- 007E: Code 1B, link -------- – Tuple CISTPL_CFTABLE_ENTRY (1B), length 8 (08) – Configuration Table Index is 00 (default) – Interface type is Memory – BVDs not ...

Page 24

CIS information (typical) Peak I = 45.0 mA -------- 00CA: Code 1B, link -------- – Tuple CISTPL_CFTABLE_ENTRY (1B), length 15 (0F) – Configuration Table ...

Page 25

SMC128CF, SMC01GCF, SMC08GCF -------- 011E: Code 1B, link -------- – Tuple CISTPL_CFTABLE_ENTRY (1B), length 6 (06) – Configuration Table Index is 03 – V Power Description: Nom V = 3.30 V, Peak I ...

Page 26

Package mechanical 12 Package mechanical Figure 2. Type I CompactFlash memory card dimensions 1.60mm ± 0.5 (0.063in ± 0.002) 3.30mm ± 0.10 (0.130in ± 0.004) 1.65mm (0.130in 0.5mm ± 0.1 (4X R 0.020in ± 0.004) 26/ ...

Page 27

SMC128CF, SMC01GCF, SMC08GCF 13 Ordering information Table 15. Ordering information scheme Example: Memory card standard SMC = storage medium, CompactFlash Density 128 = 128 Mbytes 01G = 1 Gbyte 08G = 8 Gbytes Options of the standard ...

Page 28

Revision history 14 Revision history Table 16. Document revision history Date Revision 23-Dec-2008 12-Mar-2009 05-May-2009 28/29 1 Initial release. Document status promoted from target specification to preliminary data. 2 Added SMC128CF root part number throughout the document. Added references to ...

Page 29

SMC128CF, SMC01GCF, SMC08GCF INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH NUMONYX™ PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN NUMONYX'S TERMS AND ...